HIKVISION UD.6L0201B2151A02 Quick Start Manual Download Page 5

Network Box Camera

·

Quick Start Guide

 

 

2012/19/EU (WEEE directive): Products marked 
with this symbol cannot be disposed of as unsorted 
municipal waste in the European Union. For proper 
recycling, return this product to your local supplier 

upon the purchase of equivalent new equipment, or dispose of it at 
designated collection points. For more information see: 
www.recyclethis.info 

2006/66/EC (battery directive): This product 
contains a battery that cannot be disposed of as 
unsorted municipal waste in the European Union. 
See the product documentation for specific battery 
information. The battery is marked with this symbol, 

which may include lettering to indicate cadmium (Cd), lead (Pb), or 
mercury (Hg). For proper recycling, return the battery to your 
supplier or to a designated collection point. For more information 
see

www.recyclethis.info 

Industry Canada ICES-003 Compliance

 

This device meets the CAN ICES-3 (A)/NMB-3(A) standards 
requirements. 

Safety Instruction 

These instructions are intended to ensure that user can use the 
product correctly to avoid danger or property loss.   

The precaution measure is divided into “Warnings” and “Cautions” 

Warnings: 

Serious injury or death may occur if any of the warnings 

are neglected.

 

Cautions:

 

Injury or equipment damage may occur if any of the 

cautions are neglected. 

Summary of Contents for UD.6L0201B2151A02



















































Reviews: