HIKVISION DS-K3B601SX Series Page 34 Quick Start Manual Download | Manualshive

Page: 34 / 56

background image

4.5.5 RS-485 Wiring

Note

• There are four RS-485 interfaces, which are for connecting ID card reader, IC card reader, QR

code scanner, fingerprint and card reader, card recycler, fingerprint reader, and face recognition

terminal. Take the wiring of RS-485 card reader as an example.

• When connecting the RS-485 interface with a card reader, the default entrance address is 1 and

the exit address is 4.

• If there are more than 1 RS-485 devices connected, the RS-485 ID cannot be conflicted.

4.5.6 RS-232 Wiring

Note

There are three RS-232 interfaces (UART4, UART7, and UART8). UART7 and UART8 can connect QR

code scanner, and card recycler, while UART4 can connect QR code scanner, card recycler, and face

recognition terminal.

DS-K3B601SX Series Swing Barrier Quick Start Guide

23

«
...
32
33
34
35
36
...
»

Summary of Contents for DS-K3B601SX Series

























































Reviews:

No comments

Related manuals for DS-K3B601SX Series

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

Brand: J.P. SELECTA Pages: 32

Brand: Olympus Pages: 56

Brand: Omlet Pages: 60

Brand: Valcom Pages: 6

Brand: Vaisala Pages: 60

Brand: Vaisala Pages: 146

Brand: Gaspardo Pages: 88

Brand: Yuwell Pages: 2

Brand: GE Pages: 18

Brand: Measumax Pages: 2

Brand: PHAROS MARINE Pages: 17

Brand: Lites Pages: 8

Brand: Taylor Pages: 82

Brand: Tascam Pages: 100

WEIDER SHAPE GLIDER WECR43062

Brand: ICON Health & Fitness Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands