HIKVISION DS-K3B601SX Series Page 19 Quick Start Manual Download | Manualshive

Page: 19 / 56

background image

Chapter 3 Installation

3.1 Disassemble Pedestals

Before installation, you should use the key to open the pedestals.
View the pictures below to find the lock holes.

Figure 3-1 Lock Holes

3.2 Install Pedestals

Before You Start

Prepare for the installation tools, check the device and the accessories, and clear the installation

base.
Steps

Note

• The device should be installed on the concrete surface or other non-flammable surfaces.

• If the installation area is too close to the wall, make sure the distance between the pedestal and

the wall should be more than 10 mm, or you cannot open the pedestal's top panel.

1. Prepare for the installation tools, check the components, and prepare for the installation base.

2. Drill holes on the ground according to the installation holes on the pedestals and insert the

expansion sleeves.

3. According to the entrance and exit marks on the pedestals, move the pedestals to the

corresponded positions.

DS-K3B601SX Series Swing Barrier Quick Start Guide

8

«
...
17
18
19
20
21
...
»

Summary of Contents for DS-K3B601SX Series

























































Reviews:

No comments

Related manuals for DS-K3B601SX Series

Brand: MacDon Pages: 2

Brand: MacDon Pages: 214

Brand: MacDon Pages: 32

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Sportsound SSR-300

Brand: Daktronics Pages: 42

Brand: GE Pages: 37

TOTAL KNEE 1900

Brand: Össur Pages: 58

Brand: Waves Pages: 8

Brand: CombiSteel Pages: 60

Brand: Lightolier Pages: 2

home FLP 1600 SOLAR

Brand: Somogyi Elektronic Pages: 15

Sedeo Lite Q700M

Brand: Quickie Pages: 9

Brand: Global Pages: 13

Brand: DeLaval Pages: 26

E-Boxx EV Simulator

Brand: Walther Pages: 12

GE cirrent Tetra Rigid Light Bar

Brand: Daintree Pages: 9

Brand: Berner Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands