HIKVISION DS-8000AH(F)(L)I-S Series User Manual Download

Page: 95 / 116

DS-8000AHI/AHLI/AHFLI-S Embedded Net DVR

Page

Total

116

Format HDD

Before formatting stop all recording. After formatting, you must reboot DVR, otherwise

DVR will not work normally.

6.5 Clear Alarm Out

Clear the alarm output manually.

6.6 Reboot

Reboot DVR.

6.7 Power Off

Shut down DVR.

6.8 View Log

To view the log recorded in DVR HDD.

In “Utilities” menu, press “View Log” to enter into “Log” menu:

If you want to view the log based on default option, just press

【

ENTER

】

key. DVR will list all

matched information. Also you can select options to search (By Type, By Date, and By

Type&Date).

By Type

To view log information of the assigned type

Summary of Contents for DS-8000AH(F)(L)I-S Series





















































































































Search results

Summary of Contents for DS-8000AH(F)(L)I-S Series

Reviews:

Related manuals for DS-8000AH(F)(L)I-S Series

Brands by name

Popular brands

HIKVISION DS-8000AH(F)(L)I-S Series, User Manual

Search results

Summary of Contents for DS-8000AH(F)(L)I-S Series

Reviews:

Related manuals for DS-8000AH(F)(L)I-S Series

Brands by name

Popular brands