HIKVISION DS-8000AH(F)(L)I-S Series User Manual Download Page 104

Page: 104 / 116

DS-8000AHI/AHLI/AHFLI-S Embedded Net DVR

Page

104

Total

116

The corresponding relationship of the direct cable

(2) Use the following method to make the cross network cable when DVR is directly

connected with client-end PC.

The corresponding relationship of cross cable

3 RS-232 connect cable made method

Material and tool

One twisted cable (8 pins), one standard RJ45 head, one or more DB25 or DB9 plug-in, a

tool for RJ45, one electric iron, and some soldering tin.

Pin definition

To make the RJ45 according to the following pin definition; I means DVR input, O means

DVR output.

Pin index

Name

I/O

Description

Summary of Contents for DS-8000AH(F)(L)I-S Series





















































































































Search results

Summary of Contents for DS-8000AH(F)(L)I-S Series

Reviews:

Related manuals for DS-8000AH(F)(L)I-S Series

Brands by name

Popular brands

HIKVISION DS-8000AH(F)(L)I-S Series, User Manual

Search results

Summary of Contents for DS-8000AH(F)(L)I-S Series

Reviews:

Related manuals for DS-8000AH(F)(L)I-S Series

Brands by name

Popular brands