HIKVISION DS-8000AH(F)(L)I-S Series User Manual Download

Page: 41 / 116

DS-8000AHI/AHLI/AHFLI-S Embedded Net DVR

Page

Total

116

4.8 Voice Talk

【

VOIP

】

is not available.

You can use client software to start talking with DVR.

4.9 Shut down DVR

Note: Do not switch off the power directly in case of damaging HDD. The correct step is

using “Power Off” in the “Utilities” menu, or

【

POWER

】

key on the front panel or on IR

controller.

Shut down DVR normally

Use menu

Enter into “Utilities” menu, move “Active Frame” to “Power Off” button and enter into

power off dialog, press “Confirm” to shut down the DVR.

Use

【

POWER

】

key of front panel or IR controller

Press

【

POWER

】

key for above 3 seconds.

In preview mode, a login dialog will pop-up, select user name and input password, press

【

Enter

】

to enter into power off dialog and press “Confirm” to shut down DVR. If you input error

password for three times, DVR will return preview mode.

In menu mode, if the user has “Utilities” right, you can enter into power off dialog; press

“Confirm” to shut down DVR. Otherwise, the user can not shut down DVR.

If DVR is shut down correctly, the

【

POWER

】

lamp is in red.

Note: When message of “Shut down…” is appeared, please do not press

【

POWER

】

key any

Summary of Contents for DS-8000AH(F)(L)I-S Series





















































































































Search results

Summary of Contents for DS-8000AH(F)(L)I-S Series

Reviews:

Related manuals for DS-8000AH(F)(L)I-S Series

Brands by name

Popular brands

HIKVISION DS-8000AH(F)(L)I-S Series, User Manual

Search results

Summary of Contents for DS-8000AH(F)(L)I-S Series

Reviews:

Related manuals for DS-8000AH(F)(L)I-S Series

Brands by name

Popular brands