HIKVISION DS-8000AH(F)(L)I-S Series User Manual Download

Page: 35 / 116

DS-8000AHI/AHLI/AHFLI-S Embedded Net DVR

Page

Total

116

One Channel Playback

Two Channels Playback

At the bottom of image, there is an information bar and the following information is included:

Volume, Play Progress, Play Speed, Played Time and File Total Time.



Display/Hide information bar:

【

】



Open/Close sound:

【

PLAY

】



Adjust play progress:

【

←

】

(Backward),

【

→

】

(Forward). The unit is “%”.



Adjust play speed: Normal speed is “1x”. Use

【

↑

】

to increase play speed ( 2X, 4X,

8X and MAX). Use

【

↓

】

to decrease play speed (1/2X, 1/4X, 1/8X and Frame by

Frame)



Pause/Continue: Press

【

ENTER

】

to pause/continue playback. If played frame by

frame, Press

【

ENTER

】

to paly one frame.



Copy segment:

【

EDIT

】



Exit:

【

ESC

】

Summary of Contents for DS-8000AH(F)(L)I-S Series





















































































































Search results

Summary of Contents for DS-8000AH(F)(L)I-S Series

Reviews:

Related manuals for DS-8000AH(F)(L)I-S Series

Brands by name

Popular brands

HIKVISION DS-8000AH(F)(L)I-S Series, User Manual

Search results

Summary of Contents for DS-8000AH(F)(L)I-S Series

Reviews:

Related manuals for DS-8000AH(F)(L)I-S Series

Brands by name

Popular brands