manualshive.com logo in svg

HIKVISION DS-7104NI-K1, Manual

Share
Download
HIKVISION DS-7104NI-K1 Manual Download Page 47

3. Click Apply.

5.4 Recording Management

5.4.1 Storage Device

Initialize HDD

A newly installed hard disk drive (HDD) must be initialized before it can be used to save videos and

information.
Before You Start

Install at least an HDD to your video recorder. For detailed steps, refer to Quick Start Guide.
Steps

1. Go to Configuration → Record → Storage .

2. Select an HDD.

3. Click Init.

Repair Database

Repair an HDD that with error in database. Please operate it with the help of professional

technical support.

Add Network Disk

You can add the allocated NAS or IP SAN disk to the video recorder, and use it as a network HDD.

Up to 8 network disks can be added.
Steps

1. Go to Configuration → Record → Storage .

2. Click Add.

3. Select NetHDD.

4. Set Type as NAS or IP SAN.

5. Enter NetHDD IP address.

6. Click   to search the available disks.

Network Video Recorder

34

Summary of Contents for DS-7104NI-K1



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands