Hi-Target V100 Getting Started Download Page 13

Page: 13 / 70

V100 GNSS RTK System Getting Started

Power supply

Power supply mode

Power

supply

Power supply mode

Internal

：

lithium battery

External

：

USB, Five-pin socket

External

power

supply

request

USB socket

：

DC power 4.2-5.5V/1.5A

Five-pin socket

：

DC power 6-28V/1A

When external power supply, the host will automatically detect the

voltage of lithium battery and external power supply, and choose

the higher voltage power. As for external power supply, it shall use

the special power specified by Hi-Target.

Notice: 1. The service time of lithium battery will decrease along

with

the

decrease

temperature

and

charging-discharging times increasing. A new 6300mAh

lithium battery can be used for 7 hours of static data

collection or rove work.

2. Please charge the battery within 24 hours after using

up, to extend the service life of battery, or the battery

performance will be damaged.

3. If the battery won't be used for long times, please

charge once every month to extend the service life of

battery.

Summary of Contents for V100






































































Search results

Summary of Contents for V100

Reviews:

Related manuals for V100

Brands by name

Popular brands

Hi-Target V100, Getting Started

Search results

Summary of Contents for V100

Reviews:

Related manuals for V100

Brands by name

Popular brands