Hi-Target GPS HI-TARGET HD-MAX User Manual Download Page 155

Page: 155 / 177

HD-MAX Echo Sounder User Guide

155

Figure 18-14 Uer-defined NMEA format

Select the command type of output data and set the time interval. Click [OK].

(3) Other settings of beacon receiver

Altitude cutoff angle: Refers to the cutoff angle to receive satellite signals. It

can be adjusted in 5~20.

Beacon positioning and orientating instrument

Select " K5/K7" as GPS instrument type. After GPS connection, click [Set

Rover] to enter beacon receiver parameter settings interface as shown in

Figure 15-15. After setting differential mode, output format and altitude

cutoff angle and orientating instrument parameters, click [Apply].

Figure 18-15 Beacon positioning and orientating instrument

The setup operation of differential mode, data output format and altitude

cutoff angle of beacon positioning and orientating instrument are the same

with that of the beacon receiver. Detailed information please refer to "14.4.1

Summary of Contents for HI-TARGET HD-MAX


















































































































































































Search results

Summary of Contents for HI-TARGET HD-MAX

Reviews:

Related manuals for HI-TARGET HD-MAX

Brands by name

Popular brands

Hi-Target GPS HI-TARGET HD-MAX, User Manual

Search results

Summary of Contents for HI-TARGET HD-MAX

Reviews:

Related manuals for HI-TARGET HD-MAX

Brands by name

Popular brands