Hettich Easys 200 Operating Instructions Manual Download

Page: 27 / 92

Technik für Möbel

With your furniture you have purchased a convenient electromechanical-

ly assisted opening system for refrigerators. Familiarise yourself with the

system's components and please follow the technical advice:

General information

The following safety instructions must be adhered to:

• Carefully read the operating instructions before putting the system into

operation.

• Keep the operating instructions for the entire service life of the system.
• Pass these operating instructions on to any subsequent user or owner of

the Easys.

1. Description and use

The Easys system is intended for opening refrigerator doors in domestic

furniture. The permitted ambient temperature is min. 5°C and max. 40°C. The

system is operated with a safety extra low voltage (SELV), which is generated

by the original power supply unit (included in delivery).

The system components do not have any special protection against the

penetration of water or foreign bodies and are therefore not suitable for

operation in the open or in places where exposure to water or heavy soiling

is to be expected.
Easys for refrigerators may only be used under the following conditions:

• in dry, indoor rooms

• in a temperature range of between 5°C and 40°C

No liability is accepted for damages caused through inappropriate use or

incorrect operation.

2.1 Safety precautions

• Assembly, servicing and dismantling work as well as starting up the system

and selecting settings may only be performed by a kitchen furniture

installer.

• Prior to any cleaning or servicing work, switch off the socket outlet or

disconnect the mains power plug.

• The penetration of moisture into the power supply unit presents a danger

to life from electric shock.

• Only use the power supply unit for connecting devices included with the

electromechanically assisted opening system, or devices specifically inten-

ded by the manufacturer for simultaneous connection to the power supply

unit.

• If the power supply unit's power cable is damaged, it must not be used and

must be replaced. This presents a danger to life from electric shock.

• Never open a faulty power supply unit or a faulty drive (danger to life).
• This device may only be used by persons (including children) with restricted

physical, sensory or mental capacity or who lack the necessary knowledge

and/or experience under the supervision or instruction of a person respon-

sible for their safety. Children must be supervised to ensure that they do

not play about with the device.

• The system meets the regulations applicable at the time it was released

onto the market. Other electrical devices may nevertheless interfere with

the system operation. If this occurs, contact the manufacturer or retailer of

the devices concerned.

• Cabinet doors that are to be operated by the Easys 200 must run smoothly.

Avoid any overloading or obstructing of the cabinet doors through objects

that are too heavy or bulky.

• To prevent the unintentional operation of the door, it is recommended to

connect the power supply unit to a switchable socket outlet and switch

this off as required.

2.2 Structural Modifications and Replacement Parts

Do not make any structural modifications and do not use any parts that have

not been approved by the manufacturer, as these will impair function and

safety.
• Only use genuine replacement parts.
• This also applies to the use of the Hettich power supply unit. The Hettich

power supply unit must only be used for the Easys for refrigerators.

• Only use the Easys with the genuine Hettich power supply unit.
• EC conformity will no longer apply if non-genuine replacement parts are

used.

• Components may only be replaced by a properly trained person.
• Have any damages repaired immediately by a qualified, skilled person.
• Order replacement parts from your dealer or furniture supplier.

2.3 Disposal

At the end if its useful life, dispose of your appliance in accordance with

national disposal regulations.

2.4 Marking and technical specifications

Power supply unit

1. 100…240 V 50/60 Hz = supply voltage

2. 24 V DC SELV = output voltage (safety extra low voltage)

3. 90 W = rated power

4. = protection class II (protective insulation)

Easys automatic drive and feed mechanism

5 = protection class III

6. 3.5 V = power consumption at maximum load