Heska Vet/IV 2.2 Product Manual Download Page 22 | Manualshive

Page: 22 / 30

Heska Vet/IV 2.2 Product Manual Download Page 22

Vet/IV 2.2

Infusion Pump

18

Section 11: Locking Option

The Vet/IV Pump has a unique feature that enables the user to lock the setting keys. This option prevents settings from
being changed during pump operation.

11.1 Locking

The Vet/IV Pump lockout function will disable all except SELECT, which may be used to check the progress of the infusion.

To lockout a program:

At any time during operation, simultaneously press and hold



and



. The display will show [Loc],

accompanied by a short beep.

When [Loc] is displayed, you may press

SELECT

and scroll through the various parameters, but

changes cannot be made to the settings until [Loc] is disabled.

NOTE:

[Loc] will flash on the screen when operating inlockout mode.

NOTE:

This option can only be activated while the pump is operating.

11.2 Unlocking

To deactivate or exit the lockout function, simultaneously press and hold



and



. The display will show [Loc Off ].

NOTE:

The locking function can only be deactivated while the pump is operating.

«
...
20
21
22
23
24
...
»

Summary of Contents for Vet/IV 2.2































Reviews:

No comments