Hengst WGM-B Operating Instructions Manual Download Page 10 | Manualshive

Page: 10 / 46

background image

10/46

Safety instructions

Hengst Filtration GmbH

Hengst Filtration GmbH

, RE 51550-B/04.2021

, RE 51550-B/04.2021

2 Safety instructions

2.1 Important notes

The use of the device shall only be admissible if:

▶

the product is used under the conditions described in the operating and
installation instructions, in accordance with the name plate and for the
applications for which it is intended. Hengst Filtration GmbH accepts no liability
for unauthorized modifications to the device,

▶

the information and markings on the name plates are observed,

▶

the limit values specified in the data sheet and the instructions are observed,

▶

monitoring equipment/protective devices are correctly connected,

▶

the device is protected against mechanical damage and vibrations,

▶

the service and repair work not described in these instructions is carried out
by Hengst Filtration GmbH,

▶

original spare parts are used.

These operating instructions are part of the operating equipment. The manufacturer
reserves the right to change the performance, specification or design data without
prior notice. Keep the instructions for future use.

2.2 General hazard notes

The device may only be installed by specialists who are familiar with the safety
requirements and the risks. It is imperative that you observe the safety regulations
relevant to the place of installation and the generally applicable rules of technology.
Prevent faults and thereby avoid personal injury and damage to property.

The machine end-user must ensure that:

▶

safety instructions and operating instructions are available and observed,

▶

applicable national accident prevention regulations are observed,

▶

admissible data and application conditions are complied with,

▶

safeguards are used and prescribed maintenance work is carried out,

▶

legal regulations are observed during disposal.

Maintenance, repair

During maintenance and repair work, the following must be observed:

▶

Repair works on the operating equipment may only be carried out by personnel
authorized by Hengst Filtration GmbH.

▶

Only carry out modification, maintenance or assembly works described in these
operating and installation instructions.

▶

Only use original spare parts.

«
...
8
9
10
11
12
...
»

Summary of Contents for WGM-B















































Reviews:

No comments

Related manuals for WGM-B

Brand: CAB Pages: 10

Brand: Canon Pages: 12

Brand: Unex Pages: 24

WV7220D - CCTV ACCESSORIES

Brand: Panasonic Pages: 10

WV-NS202 - i-Pro Network Camera

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 4

BB-HGW700A - Network Camera Router

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 19

Brand: Panasonic Pages: 59

Brand: Zacuto Pages: 4

Brand: i-PRO Pages: 2

Brand: JANE Pages: 6

Brand: Obelink Pages: 2

Brand: Leuze Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands