HEMCO UniFlow CE Installation, Operation & Maintenance Manual Download Page 2

Page: 2 / 12

Table of Contents

GENERAL SYSTEM DESCRIPTION.........................................................................................3

RECEIVING AND INSPECTING SHIPMENTS......................................................................... 4

PREPARATION FOR INSTALLATION...................................................................................... 5

SUGGESTED TOOL LIST......................................................................................................... 5

REQUIRED TOOL LIST ........................................................................................................... 5

INSTALLATION......................................................................................................................... 6

MAINTENANCE....................................................................................................................... 10

General System Description

UniMax Floor Mount Hood is constructed and equipped with:

• Modular Construction featuring wall panels that are 2” thick with chemical

resistant composite resin surface skin panels.

• Structural framework to be clear of anodized aluminum extrusions.

• A rear varaﬂ ow baﬄ e is mounted on the rear wall of hood.

• Top mounted exhaust collar(s).

HEMCO

Laboratory Planning Solutions

www.HEMCOcorp.com

[email protected]

Fax (816) 796-3333

Tel (816) 796-2900

HEMCO Corporation
711 South Powell Road
Independence, MO 64056

Notes:

Summary of Contents for UniFlow CE













Search results

Summary of Contents for UniFlow CE

Reviews:

Related manuals for UniFlow CE

Brands by name

Popular brands

HEMCO UniFlow CE, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for UniFlow CE

Reviews:

Related manuals for UniFlow CE

Brands by name

Popular brands