background image

  18 

Limited Warranty 

HELTUN warrants this product to be free from defects in workmanship or materials, under normal use and service, for 
a  period  of  one  (1)  year  from  the  date  of  purchase  by  the  consumer  ("Warranty  Period").  HELTUN  will  extend  this 
Warranty Period to three (3) years from the date of consumer purchase for any consumer who registers his/her product 
with HELTUN at this website page: bonus.heltun.com. This Limited Warranty applies only to the first end-user of the 
product and is not transferable. 
 
If during the Warranty Period the product is determined to be defective or malfunctions due to workmanship or materials, 
HELTUN, at HELTUN's option, shall either repair or replace the defective product. If the product is defective, (i) return 
it  with  dated  proof  of  purchase  to  the  place  it  was  purchased;  or  (ii)  contact  HELTUN  Customer  Care  by  email  at 
[email protected]. HELTUN Customer Care will make the determination whether the product should be returned or 
whether a replacement product will be sent to you. 
 
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THIS LIMITED WARRANTY IS IN LIEU OF 
ALL  OTHER  COVENANTS  AND  WARRANTIES,  EITHER  EXPRESS  OR  IMPLIED,  INCLUDING  WITHOUT 
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTIBILITY OR FITNESS FOR A PARTICULAR PURPOSE, 
OR NON-INFRINGEMENT. HELTUN MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. 
 
THIS  LIMITED  WARRANTY  DOES  NOT  COVER  REMOVAL  OR  REINSTALLATION  COSTS.  THIS  LIMITED 
WARRANTY  SHALL  NOT  APPLY  IF  IT  IS  SHOWN  BY  HELTUN  THAT  THE  DEFECT  OR  MALFUNCTION  WAS 
CAUSED BY DAMAGE DONE BY A CONSUMER INCLUDING DURING INSTALLATION. THIS LIMITED WARRANTY 
IS VOID IF DEFECT(S) RESULT FROM A FAILURE TO HAVE THIS PRODUCT INSTALLED PROPERLY. 
 
HELTUN'S SOLE RESPONSIBILITY AND THE CONSUMER'S SOLE REMEDY UNDER THIS LIMITED WARRANTY 
SHALL BE TO REPAIR OR REPLACE THE PRODUCT WITHIN THE TERMS STATED ABOVE. HELTUN SHALL NOT 
BE  LIABLE  FOR  ANY  LOSS  OR  DAMAGE  OF  ANY  KIND,  INCLUDING  ANY  INCIDENTAL  OR  CONSEQUENTIAL 
DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR 
IMPLIED,  OR  ANY  OTHER  FAILURE  OF  THIS  PRODUCT.  IN  NO  EVENT  SHALL  HELTUN'S  LIABILITY  EXCEED 
THE AMOUNT ACTUALLY PAID FOR THE PRODUCT WHETHER SUCH LIABILITY ARISES FROM A CLAIM BASED 
ON WARRANTY, TORT, OR CONTRACT. THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN EFFECT EVEN 
IF HELTUN WAS ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR DAMAGES. 
 
SOME  JURISDICTIONS  DO  NOT  ALLOW  THE  EXCLUSION  OR  LIMITATION  OF  INCIDENTAL  OR 
CONSEQUENTIAL  DAMAGES,  SO  THIS  LIMITATION  MAY  NOT  APPLY  TO  YOU.  THIS  LIMITED  WARRANTY  IS 
THE ONLY EXPRESS WARRANTY HELTUN MAKES ON THIS PRODUCT.  
 
If you have any questions concerning this limited warranty, please write HELTUN Customer Care at [email protected]

 

HELTUN, INC. USA DELAWARE CORPORATION.

 

2/5 ARMENAKYAN STR., YEREVAN, 0047, ARMENIA

 

WWW.HELTUN.COM

 

[email protected]

 

Summary of Contents for HE-TPS04



















Reviews: