background image

page 39 of 61

Documents are only to be used and distributed completely and unchanged. It is strictly the users´ responsibility to check carefully 

the validity of this document with respect to his product. Manual-no.: 999248 / 28/04/2011

The controller is equipped with a serial interface (RS 232C, nine-pole Sub-D-plug).

  Plug-in or remove the cable (cable RS 232C) from the interface only if the equipment is switched off.

  The interface is 

not

 electrically isolated from the measuring circuit.

  For optimal electromagnetic compatibility assemble an interface filter (cat. no.: 638235).

The controller is fully operable via the serial interface. Measuring results, preselections and the status of 

the controller can be read at any time.

 7.1 Setting of the interface

Set the interface parameters directly at the controller. The factory set values are underlined.

Edit and confirm the interface parameters in the function ”Configuration” in the menu ”RS-232” using the 

selection knob.

  Baud: 2400, 4800, 9600 or 19200

  Parity: 8-N-1, 7-O-1 or 7-E-1

  Handshake: Off, Xon-Xoff or 

RTS-CTS

  Remote: On or Off

  Timeout: Sending 1s, receiving 10s.

In remote mode  (Remote On, ”PC symbol” in the display) all keys at the controller are inoperable.

To return to the manual operation of the controller set the controller to ”Remote off” in menu 

configuration.  Therefore switch off the controller. Switch on the controller and press selection 

knob within 2s.

  A maximum of ten commands per second is possible.

  Read commands and commands ”REMOTE”, ”CVC” and ”STORE” can be sent always. The sending 

of other write commands is only possible, if ”Remote on” is selected.

  The commands have to be written in capital letters.

  Command and parameter have to be separated by a blank.

  The string is terminated with <CR> or <CR><LF>. 

  The answer of the controller is always terminated with <CR><LF>.

  Numerical values and parameters can be written without leading zeros.

  The answer of the controller is always with leading zeros.

7 Interface parameters

Summary of Contents for ROTAVAC






























































Reviews: