background image

Telephone: 

0117 923 5375

 Fax: 

0117 923 5374

Victoria Road, Avonmouth, Bristol BS11 9DB
www.heatstore.co.uk

Waste electrical products should not be disposed of with household waste. Please 

recycle where facilities exist. Check with your local authority or retailer for recycling 

advice. 3 Year Warranty. ISSUE 1 HSUFDC 0415

IP

THREE YEAR

32

3

Technical Specification

Size

Minimum wall box depth

Total Load

90mm (H) x 86mm (W) x 

43mm (D)

30mm

16A

Operating ambient temperature

Voltage

Protective housing

-5 to +40ºC

230V

IP32

Temperature Limit

1.  Press   to switch the unit off, then press and hold both the   and

 buttons together for  five seconds. Use 

 and   to select “3LIT”.

2.  Use   and   to set the desired temperature limit. Press   to save 

your settings and exit. Check with your floor finish manufacture for 

guidance on maximum temperature.

Temperature Calibration

 

1.  Press   to switch the unit off then press and hold both the   

and

 buttons together for  five seconds. Use 

 and   to select 

“1ADJ”.

2.  Use   and   to adjust the measured temperature. Press   to save 

your settings and exit.

Summary of Contents for HSUFDC









Reviews: