Heatilator NNXT33-IFT Installation Manual Download Page 53

Page: 53 / 67

Heatilator • NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual • 2628-980 Rev. C • 8/20

G. Install Logs

LOG PLACEMENT INSTRUCTIONS

Figure 3. Log #4 in Position

Log Set Assembly: SRV2384-070, SRV2385-070
Models: NNXT33-IFT, NNXT33L-IFT

NNXT36-IFT, NNXT36L-IFT

See Table 1 for corresponding log set and individual logs

for each size Novus model.

Figure 1. Log Set Shown as Shipped

Figure 2. Locations of Flat Spots for Log #4

CAUTION:

Logs are fragile, handle with care.

FLAT SPOTS FOR LOG #4

LOG #4:

Place Log #4 into position by setting the left end of Log #4 into the flat spot on Log #2 and then resting the right

end, or nose, of Log #4 on the flat spot on Log #1. Figure 2 shows locations of flat spots. Figure 3 shows Log #4 installed.

SIZE

ASSEMBLY

SRV2384-070

SRV2385-070

LOG 1

SRV2384-071

LOG 2

SRV2380-072

SRV2381-072

LOG 3

SRV2384-073

SRV2385-073

LOG 4

SRV2380-074

LOG 5

SRV2384-075

SRV2385-075

LOG 6

SRV2384-076

SRV2385-076

Table 1.

The log set is shipped from the factory with three logs

already in place on the hearth pan. See Figure 1.

Summary of Contents for NNXT33-IFT




































































Search results

Summary of Contents for NNXT33-IFT

Reviews:

Heatilator NNXT33-IFT, Installation Manual, Page: 53 / 67

Search results

Summary of Contents for NNXT33-IFT

Reviews: