manualshive.com logo in svg

Heatilator NNXT33-IFT, Installation Manual, Page: 43 / 67

Share
Download
Heatilator NNXT33-IFT Installation Manual Download Page 43

43

Heatilator  •  NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual  •  2628-980  Rev. C  •  8/20

G.  Shrouds

•  Chase  top  shrouds  may  be  field  constructed  where 

permitted by regional building codes.

WARNING! Risk of Fire! 

Shrouds must be constructed 

as specified. Improper construction may overheat chase 

top.

NOTICE: 

Some regional codes require an agency-

Listed shroud. Consult your local building officials.

•  The following field constructed shroud designs have 

been tested for Hearth Technologies fireplace systems 

and termination caps. 

•  The shrouds must be constructed from a minimum .018 

in. (26 ga) thick aluminized steel.

•  The wire mesh is optional but recommended and must 

be .018 in. thick minimum, 1/2 in. mesh.

HHT Shrouds

•  You may install a shroud with this fireplace. See 

Section 12.B for a list of UL Listed shrouds. Follow the 

instructions included with these optional components

Min.

Base Dim.

Min.

Base Dim.

Min. 

Top Dim.

Min. 

Top Dim.

Figure 7.16  Open Top Shroud Dimensions

Field Constructed Shrouds

Open Top Shroud (may be used with DVP-TV, DVP-

TVHW, SLP-TVHW)

Min. Base Dims.

in

19 x 19

mm

483 x 483

Min. Top Dims.

in

16 x 16

mm

406 x 406

Min. Base Dim

Min. Height

Min.

Base Dim

Figure 7.17  Mailbox Style Shroud Dimensions

Minimum

Opening

Height

Minimum

Base Dimension

Min. Opening

Width

Min. Base Dimension

Minimum

 Height

Figure 7.18  Roofed Style Shroud Dimensions

Roofed Style Shroud (may be used with DVP-TV, 

DVP-TVHW, SLP-TVHW)

Mailbox Style Shroud (may be used with DVP-TV, 

DVP-TVHW, SLP-TVHW)

Min. Base Dims.

in

20 x 20

mm

508 x 508

Min. Height

in

18

mm

457

Min. Base Dims.

in

20 x 20

mm

508 x 508

Min. Height

in

18

mm

458

Min. Opening Width

in

14

mm

356

Min. Opening Height

in

10

mm

254

Summary of Contents for NNXT33-IFT




































































Reviews:

No comments