Heatilator NNXT33-IFT Installation Manual Download Page 49

Page: 49 / 67

Heatilator • NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual • 2628-980 Rev. C • 8/20

Finishing

B. Mantel and Wall Projections

WARNING! Risk of Fire!

Comply with all minimum clear-

ances to combustibles as specified. Framing or finishing

material closer than the minimums listed must be construct

ed entirely of non-combustible materials (i.e., steel studs,

concrete board, etc).

Measured from top of hood or top of appliance opening (in inches)

Refer to Section 3 for additional clearances to combustibles information.

5-1/2

6-1/4

7-3/4

8-1/2

9-1/4

10-3/4

11-1/2

12-1/4

13-3/4

14-1/2

15-1/4

30 in. minimum

to ceiling

Figure 10.1

Minimum Vertical and Maximum Horizontal

Dimensions

Note:

All

measurements

in inches

Figure 10.2 Mantel Leg or Wall Projections (Acceptable on both

sides of opening)

Combustible Mantels

Combustible Mantel Legs or Wall Projections

Note:

Mantel measurement is taken from top of the

opening, NOT the top of the fireplace.

MANTEL LEG OR

PERPENDICULAR WALL

TOP OF

APPLIANCE

DRYWALL

FIREPLACE

OPENING

See Dimension B on

Appliance Dimension

Diagram.

UNLIMITED

STOP FINISHING MATERIAL

FLUSH WITH OUTSIDE EDGE

OF APPLIANCE.

1 in. (max)

1 in.

(min)

3-1/2 in.

(min)

NOTICE:

Surface temperatures around the appliance will

become warm while the appliance is in operation. Ensure

finishing materials used for all surfaces (floor, walls,

mantels, etc.) will withstand temperatures up to 190

Risk of Fire!
DO NOT

apply combustible materials beyond the min-

imum clearances.

Comply with all minimum clearanc-

es to combustibles as specified in this manual.

terials overlapping into non-combustible zones could

ignite and will interfere with air flow through decorative

barrier fronts.

• Metal front of appliance may be covered with non-

combustible materials only.

• Facing and/or finishing materials must not interfere

with air flow through

decorative barrier fronts, removal

of decorative barrier fronts or access for service.

• Facing and/or finishing materials must never

overhang into the glass opening.

• Observe all clearances when applying combustible

materials.

• Seal gaps between the finished wall and appliance

top and sides using a 300 ºF minimum sealant.

WARNING

A. Facing Material

Summary of Contents for NNXT33-IFT




































































Search results

Summary of Contents for NNXT33-IFT

Reviews:

Heatilator NNXT33-IFT, Installation Manual, Page: 49 / 67

Search results

Summary of Contents for NNXT33-IFT

Reviews: