manualshive.com logo in svg

Heatilator NNXT33-IFT, Installation Manual, Page: 34 / 67

Share
Download
Heatilator NNXT33-IFT Installation Manual Download Page 34

Heatilator  •  NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual  •  2628-980  Rev. C  •  8/20

34

6 

6 

Appliance Preparation 

CAUTION! 

Risk  of  Cuts, Abrasions  or  Flying  Debris. 

Wear protective gloves and safety glasses during installa-

tion. Sheet metal edges are sharp.

NOTICE: 

Once appliance is set up for top or rear venting, 

it CANNOT be changed at a later time.

A.  Top Vent

Figure 6.1  

Figure 6.2  

Figure 6.3  

Figure 6.4  

Figure 6.5  

•  Discard the vent cap, remove and discard the insulation 

basket  from  the  inner  vent  pipe. 

 Note: 

 Once the 

vent  cap has been removed it cannot be reattached.  

Remove insulation from outer vent pipe. 

•  Fold the center parts of the retaining band up and use 

to remove the vent cap.

•  Remove the cover plate by removing the two screws 

holding it to the top of the appliance. Remove and discard 

the cover plate.

•  Remove the center insulation plug.

•  Cut the metal retaining band and fold the sides out.

•  Snap the first vent section into place.

Proceed to Section 6.B or 6.C.

Figure 6.6  

Summary of Contents for NNXT33-IFT




































































Reviews:

No comments