manualshive.com logo in svg

Heatilator NNXT33-IFT, Installation Manual, Page: 52 / 67

Share
Download
Heatilator NNXT33-IFT Installation Manual Download Page 52

Heatilator  •  NNXT33-IFT, NNXT33L-IFT, NNXT36-IFT, NNXT36L-IFT Installation Manual  •  2628-980  Rev. C  •  8/20

52

F.   Install Decorative Barrier Front

WARNING!  Risk of Fire! 

Install ONLY doors or fronts 

approved by Hearth & Home Technologies. Unapproved 

doors or fronts could cause fireplace to overheat.

This  fireplace  has  been  supplied  with  an  integral 

barrier to prevent direct contact with the fixed glass 

panel. DO NOT operate the fireplace with the barrier 

removed. 

Contact  your  dealer  or  Hearth  &  Home  Technologies  if 

the barrier is not present or help is needed to properly 

install one.
For more information refer to the instructions supplied with 

your decorative barrier front.

E.  Install Fixed Glass Assembly

WARNING! 

Risk  of  Asphyxiation! 

Handle  fixed  glass 

assembly  with  care.  Inspect  the  gasket  to  ensure  it  is 

undamaged  and  inspect  the  glass  for  cracks,  chips  or 

scratches. 

• 

DO NOT

 

strike, slam or scratch glass.

• 

DO NOT

 

operate fireplace with glass removed, cracked, 

broken or scratched.

• 

Replace as a complete assembly.

•  Set the glass panel on the lower two glass assembly 

latches, ensuring the glass panel is centered in the 

opening.

•  Replace glass latches.

Figure 11.3  Placement of Mineral Wool, Lava Rock and Vermiculite

LAVA ROCK AND VERMICULITE

MINERAL WOOL

REAR BURNER 

PORT HOLES

FRONT BURNER 

PORT HOLES

DO NOT PLACE LAVA ROCK OVER 

SLOTS IN BASEPAN

DO NOT PLACE LAVA ROCK OVER 

SLOTS IN BASEPAN

MINERAL WOOL OR LAVA 

ROCK (IF DESIRED)

MINERAL WOOL OR LAVA 

ROCK (IF DESIRED)

Figure 11.2  Control Heat Shield - Installed

•  Make sure all wires are under the top of the control heat 

shield and that there are no wires pinched between legs 

and the control heat shield.

D.  Install Control Heat Shield

The control heat shield 

MUST

 be placed over the control 

plate before operating the appliance. Not doing so may 

result in overheating the controls on the plate.

•  Verify that the control heat shield is installed and legs 

are on bottom pan of appliance. See Figure 11.2.

Figure 11.4  Fixed Glass Assembly

Latches

(both bottom 

and top)

Glass 

Assembly

Control Heat Shield in Place

Control Heat Shield in Place

Summary of Contents for NNXT33-IFT




































































Reviews:

No comments