background image

 

To see operational and troubleshooting information and videos,

 

3

 

go to www.hzsupport.com

 

210008-02

INSTALLATION

 WARNING: Turn power off at circuit breaker or fuse. 

Place tape over circuit breaker switch and verify power is 

off at the fixture.

This fixture comes with a “Easy Install” mounting plate. It is pre-

assembled on the fixture for shipping.

1.  Unscrew the large mounting bolt connecting the light fixture to 

the mounting plate and remove the mounting plate (see Figure 1). 

The mounting bolt is designed to stay in the light fixture.

2.  Install the mounting bracket with the stamped word “FRONT” 

facing away from the junction box (see Figure 2). Use the mount-

ing bracket screws that best fit the junction box.

3.  Route the junction box wires through the hole in the mounting 

plate (see Figure 3).

4.  Place the mounting plate against the junction box (see Figure 3).

•  Wall Mounted – The “UP” arrow must point upward

•  Eave Mounted – The “UP” arrow must point toward the building

5.  Insert the small mounting bolt through the mounting plate hole 

located below the threaded hole. Thread the bolt into the center 

hole of the mounting bracket (see Figure 3). Tighten bolt securely.

WIRING

Insert the junction box wires into the side of the terminal block and 

around the ground screw (see Figure 4). Tighten terminal block screws 

and ground screw to secure wires.

•  White to “N (White)”

•  Black to “L (Black)”

•  Bare or green ground wire to GND (ground) screw.

FINAL ASSEMBLY

1.  Double check that all wiring connections are securely connected.

2.  Align the bottom edge of the light fixture with the bottom edge 

of the mounting plate. Tilt the light fixture toward the mounting 

plate, making sure the light fixture is centered on the mounting 

plate.

 

IMPORTANT:

 The two pins on the rear of the light fixture must 

insert into the terminal block for the light to work.

3.  Tighten the mounting bolt securely being careful not to overtighten 

(see Figure 5).

Figure 1

Figure 2

Figure 3

Figure 4

FR

ON

T

FR

ON

T

FR

ON

T

N (W

hite/

Blanc

/Blan

co)

GN

D

Terre

Tierra

UP/Hau

t/Arri

ba

L (Bla

ck/

Noir/

Negro

)

FR

ON

T

N (W

hite/

Blanc

/Blan

co)

GN

D

Terre

Tierra

UP/Hau

t/Arri

ba

L (Bla

ck/

Noir/

Negro

)

N (White/

Blanc/Blanco)

GND

Terre

Tierra

UP/Haut/Arriba

L (Black/

Noir/Negro)

Summary of Contents for 5838





























Reviews: