Heat & Glo SL-350TRS-CE-D Installer'S Manual Download Page 36

Page: 36 / 47

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. V • 3/13

Figure 54. Sealant Material

Installing the Trim

Combustible materials may be brought up to the speci-

fied clearances on the side and top front edges of the

fireplace, but

MUST NEvER

overlap onto the front

face. The joints between the finished wall, fireplace top

and sides can only be sealed with a 150º C minimum

sealant.
Install optional marble and brass trim surround kits as

desired. Marble, brass, brick, tile, or other noncombus-

tible materials can be used to cover up the gap between

the sheet rock and the fireplace.
Do not obstruct or modify the air inlet/outlet grilles.

When overlapping on both sides, leave enough space

so that the bottom grille can be opened and the trim

door removed.

Step 10

Installing Trim,

Logs, and

Ember Material

1. Apply only non-

combustible facing

material to the

fireplace surround.

cauTiON

wARNING: CHILDREN AND ADULTS

SHOULD BE ALERTED TO THE HAZARDS

if JOiNTs beTweeN The fiNisheD walls aND

The fireplace surrOuND (TOp aND siDes)

are sealeD, a 150º

c. miNimum sealaNT ma

Terial musT be useD. These JOiNTs are

NOT reQuireD TO be sealeD. ONly NONcOm

busTible maTerial (usiNG 150º c. miNimum

aDhesive, if NeeDeD) caN be applieD as

faciNG TO The fireplace surrOuND. see

The DiaGram belOw.

OF HIGH TEMPERATURES OF wORKING

SURFACES ON THESE HEATERS. wORKING

SURFACES INCLUDE ALL GLASS PANELS

AND DECORATIvE DOORS. YOUNG CHILDREN

SHOULD BE CAREFULLY SUPERvISED wHEN

THEY ARE IN THE SAME ROOM AS THE AP-

PLIANCE.

FINISH MATERIAL

MAY BE COMBUSTIBLE

-TOP AND SIDES OF UNIT-

SIDE

SEAL

JOINT

TOP SEAL

JOINT

1,27 cm

Summary of Contents for SL-350TRS-CE-D
















































Search results

Summary of Contents for SL-350TRS-CE-D

Reviews:

Related manuals for SL-350TRS-CE-D

Brands by name

Popular brands

Heat & Glo SL-350TRS-CE-D, Installer'S Manual

Search results

Summary of Contents for SL-350TRS-CE-D

Reviews:

Related manuals for SL-350TRS-CE-D

Brands by name

Popular brands