Heat & Glo SL-350TRS-CE-D Installer'S Manual Download Page 30

Page: 30 / 47

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. V • 3/13

Important Notice:

Heat shields may not be field constructed.

L. Heat Shield Requirements for Horizontal

Termination

For all horizontally vented appliances, a heat shield MUST

be placed 2.5 cm above the top of the flue pipe between the

wall shield firestop and the base of the termination cap.
There are two sections of the heat shield. One section

is factory-attached to the wall shield firestop. The other

section is factory-attached to the cap. See Figure 47.
If the wall thickness does not allow the required 4 cm heat

shield overlap when installed, an extended heat shield

must be used.

warNiNG! risk of fire!

To prevent overheating and fire,

heat shields must extend through the entire wall thickness.

Heat shields must overlap 4 cm minimum.

•

DO NOT

remove the heat shields attached to the wall

shield firestop and the horizontal termination cap (shown

in Figure 47).

• If the wall thickness is less than 10 cm (DVP) or 11 cm

(SLP), the heat shields on the cap and wall shield firestop

must to be trimmed. A minimum 4 cm overlap MUST be

maintained.

• Use an extended heat shield if the finished wall thickness

is greater than 18.4 cm.

• The extended heat shield may need to be cut to length

maintaining sufficient length for a 4 cm overlap between

heat shields.

• Attach the extended heat shield to either of the existing

heat shields using the screws supplied with the extended

heat shield.

• Rest the small leg on the extended heat shield on top

of the pipe section to properly space it from the pipe

section.

Install Horizontal Termination Cap

warNiNG! risk of fire!

The telescoping flue section of

the termination cap MUST be used when connecting flue

pipe.

• 38 cm) minimum overlap of flue telescoping section

is required.

Failure to maintain overlap may cause overheating and

fire.

• Termination caps must not be recessed in the wall. Siding

may be brought to the edge of the cap base.

• Flash and seal as appropriate for siding material at

outside edges of cap.

cauTiON! risk of burns!

Local codes may require in-

stallation of a cap shield to prevent anything or anyone

from touching the hot cap.

Figure 47 venting through the wall

INTERIOR

HEAT SHIELD OR

EXTENDED

HEAT SHIELD

WALL SHIELD

FIRESTOP

HEAT SHIELD

4 cm MIN.

OVERLAP

SHEATHING

SLIP SECTION

CAN BE EXTENDED

INNER FLUE

OUTER FLUE

EXTERIOR

Note:

When using termination caps with factory-supplied

heat shield attached, no additional wall shield firestop is

required on the exterior side of a combustible wall.

NOTice:

For certain exposures which require superior

resistance to wind-driven rain penetration, a flashing kit and

HRC caps are available. When penetrating a brick wall, a

brick extension kit is available for framing the brick.

Summary of Contents for SL-350TRS-CE-D
















































Search results

Summary of Contents for SL-350TRS-CE-D

Reviews:

Related manuals for SL-350TRS-CE-D

Brands by name

Popular brands

Heat & Glo SL-350TRS-CE-D, Installer'S Manual

Search results

Summary of Contents for SL-350TRS-CE-D

Reviews:

Related manuals for SL-350TRS-CE-D

Brands by name

Popular brands