Heat & Glo SL-350TRS-CE-D Installer'S Manual Download Page 3

Page: 3 / 47

Heat & Glo • SL-350TRS-CE-D • 2033-900 Rev. V • 3/13

Table of

Contents

Safety and Warning Information

.................................................................... 2

Service Parts List ............................................................................................ 4

Section 1: Approvals and Regulations .......................................................... 7

Appliance Certification ..................................................................................

Installation Regulations ................................................................................

Section 2: Getting Started .............................................................................. 8

Introducing the Heat & Glo Gas Fireplaces ..................................................

Pre-installation Preparation ..........................................................................

Section 3: Installing the Fireplace ............................................................... 10

Step 1

Locating the Fireplace................................................................ 10

Step 2

Framing the Fireplace ................................................................ 11

Step 3

Installing the Flue System .......................................................... 12

A. Flue System Approvals.......................................................... 12

B. Flue Pipe Clearances to Combustibles ................................. 23

C. Wall Penetration Framing ...................................................... 23

D. Vertical Penetration Framing ................................................. 24

E. Assemble Flue Pipe Sections (DVP Pipe Only) .................... 25

F. Assemble Flue Pipe Sections (SLP Pipe Only)...................... 26

G. Assemble SLP or DVP Slip Sections .................................... 26

H. Securing the Flue Pipe Sections (DVP and SLP Pipe) ......... 27

I. Installing Metal Roof Flashing ................................................. 28

J. Installing Vertical Termination Cap ........................................ 29

K. Assemble and Install Storm Collar ........................................ 29

L. Heat Shield Requirements for Horizontal Termination ........... 30

Step 4

Positioning, Leveling and Securing the Fireplace ...................... 32

Step 5

The Gas Control Systems .......................................................... 32

Step 6

The Gas Supply Line ................................................................. 33

Step 7

Gas Pressure Requirements...................................................... 34

Step 8

Wiring the Fireplace ................................................................... 34

Step 9

Finishing..................................................................................... 35

Step 10 Installing Trim, Logs & Ember Material ......................................... 36

Installing the Trim....................................................................... 36

Positioning the Logs................................................................... 37

Placing the Ember Material ........................................................ 39

  Step 11  Before Lighting the Fireplace ..................................................... 40
  Step 12  Lighting the Fireplace................................................................. 40

After the Installation .................................................................. 40

Section 4: Maintaining and Servicing Your Fireplace ................................ 41

Section 5: Troubleshooting .......................................................................... 43

Limited Lifetime Warranty ................................................................................ 46



= Contains updated information.



Summary of Contents for SL-350TRS-CE-D
















































Search results

Summary of Contents for SL-350TRS-CE-D

Reviews:

Related manuals for SL-350TRS-CE-D

Brands by name

Popular brands

Heat & Glo SL-350TRS-CE-D, Installer'S Manual

Search results

Summary of Contents for SL-350TRS-CE-D

Reviews:

Related manuals for SL-350TRS-CE-D

Brands by name

Popular brands