Heartland 16615-G Assembly Manual Download

Page: 18 / 71

PARTS REQUIRED:

2" (5,1 cm)

x150

1-1/2"

(3,8 cm)

3" (7,6 cm)

12' FRONT WALL

48 x 84" (121,9 x 213,4 cm )

Install the left door panel
on wall frame, 1-1/2" from
the top plate.
Use a 2x4 spacer for
consistent measurement.
Secure panel with 2"
nails spaced 6" apart
on edges.

Install the right door panel

fl ush to installed panel,

as shown.
Ensure 64" (162,6 cm) door
measurement.
Use part

as a

temporary brace.
Secure with with (2)
3" screws.

Secure panel with 2"
nails spaced 6" apart
on edges.

2x4

Flush

64"

(162,6 cm)

Install

48" x 84"

window

cutout panel fl ush to

installed panel and
1-1/2" from the
top plate.

Secure panel with 2"
nails spaced 6" apart
on edges and 12" apart
inside panel.

Your 12' front wall is
now assembled.

Carefully fl ip

the wall over.

FINISH

BEGIN HERE

3/4"

(1,9 cm)

1-1/2"

(3,8 cm)

(15,2 cm)

3/4" Gauge

Block

Flush

12"

(30,5 cm)

2x4

Flush

(15,2 cm)

OO Temporary Brace

(7,6 cm)

Screw

(7,6 cm)

Screw

69" (175,3 cm) Door Stiffener

Temporary Brace

Summary of Contents for 16615-G








































































Search results

Summary of Contents for 16615-G

Reviews:

Related manuals for 16615-G

Brands by name

Popular brands

Heartland 16615-G, Assembly Manual

Search results

Summary of Contents for 16615-G

Reviews:

Related manuals for 16615-G

Brands by name

Popular brands