background image

7019-801C

July 10, 2019

25

SANTA FE PELLET INSERT

Mobile Home Installation

You must use a Quadra-Fire Outside Air Kit for 

installation in a mobile home.

1.  An outside air inlet must be provided for the 

combustion air and must remain clear of leaves, debris, 

ice and/or snow. It must be unrestricted while the 

appliance is in use to prevent room air starvation which 

causes smoke spillage. Smoke spillage can also set off 

smoke alarms.

2.  The combustion air duct system must be made of 

metal. It must permit zero clearance to combustible 

construction and prevent material from dropping into 

the inlet or into the area beneath the dwelling and 

contain a rodent screen.

3.  The appliance must be secured to the mobile home 

structure by bolting it to the floor (using lag bolts). 

Use the same holes that secured the appliance to the 

shipping pallet.

4.  The appliance must be grounded with #8 solid copper 

grounding wire or equivalent, terminated at each end 

with an NEC approved grounding device.

5. 

Refer to Clearances to Combustibles and floor 

protection requirements on 

page 8

 for listings to 

combustibles and appropriate chimney systems.

6.  Use silicone to create an effective vapor barrier at 

the location where the chimney or other component 

penetrates to the exterior of the structure.

7.  Follow the chimney manufacturer’s instructions when 

installing the vent system for use in a mobile home.

8.  Installation shall be in accordance with the 

Manufacturers Home & Safety Standard (HUD) CFR 

3280, Part 24

.

PART NUMBER: 811-0872

Spark Arestor Cap 

Roof Flashing 

Storm Colla

Joist Shield/Firestop 

Double Wall 

Connector Pipe  

Figure 25.1

CAUTION

THE STRUCTURAL INTEGRITY OF THE MOBILE 

HOME FLOOR, WALL AND CEILING/ROOF MUST BE 

MAINTAINED

Do NOT cut through:

•  Floor joist, wall, studs or ceiling trusses.

•  Any supporting material that would affect the 

structural integrity.

This appliance is to be connected to a factory-built 

chimney conforming to 

CAN/ULC-S629, Standard for 

650°C Factory-Built Chimneys

.

For removal of the chimney for mobile home 

transportation, contact the proper transportation officials.

WARNING

Products of combustion generate carbon monoxide 

and different fuels generate different levels. Carbon 

monoxide

• 

Only use approved fuels in this appliance.

• 

Always keep door shut during operation. Operating 

this appliance with doors open can allow CO to leak 

into the home.

CO can kill you before you are aware it is in your home. 

At lower levels of exposure, CO causes mild effects 

that are often mistaken for the flu. These symptoms 

include headaches, dizziness, disorientation, nausea 

and fatigue. The effects of CO exposure can vary greatly 

from person to person depending on age, overall health 

and the concentration and length of exposure.

CAUTION

Never draw outside combustion air from:

• 

Wall, floor or ceiling cavity

•  Enclosed space such as an attic or garage

WARNING

It is critical to have a working smoke detector 

installed in the home of appliance operation.

•  Smoke alarms that are properly installed and 

maintained play a vital role in reducing fire deaths 

and injuries. Having a working smoke alarm reduces 

the chance of fire related injuries.

Summary of Contents for Quadra-Fire SANTA FE SANTAFEI-C

































Reviews: