background image

1

Hearth & Home Technologies  •  Vertical Power Vent  (PVV-SLP) Instructions •  4071-900 Rev. C  •  11/19

PVV-SLP

Power Vent Vertical

- Installation Instructions -

Introduction  

DO NOT DISCARD THIS MANUAL

NOTICE

•  Leave this manual with 

party responsible for use 

and operation.

DO NO

T

DISCARD

•  Important operating 

and maintenance 

instructions included.

•  Read, understand and follow 

these instructions for safe 

installation and operation.

IMPORTANT:

  Failure to read and follow these instruc-

tions may create a possible hazard and will void the fire

-

place warranty.

These instructions must remain with the equipment.

CAUTION! Risk of Cuts or Abrasions. 

Wear protective 

gloves and safety glasses during installation. Sheet metal 

edges are sharp.

Installation of the PVV-SLP may be done by a qualified 

service technician only. Installation MUST comply with 

local, regional, state and national codes and regulations. 

KIT COMPONENTS

•   Vertical Power Vent
•   Storm Collar
•   Flue Restrictor
A minimum of one PVV-SLEEVE is required.  Additional 

sleeves may be needed based on installation.  Order 

separately.

Table of Contents

1 Introduction 

 

A.  Installation of PVV-SLP  . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Vent Information and Diagrams 

 

A.  Installation of Vent Pipe  . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
B.  Vent/Pipe Regulations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
C.  Venting Length - Model Categories and Length 
  Requirements by Termination Type  . . . . . . . . . . . . . . . . . . 5
D. Setting the PVV-SLP Flue Restictor  . . . . . . . . . . . . . . . . . . 6

3 Framing and Clearances 

 

A.  Framing and Clearances  . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B.  Vent Termination Minimum Clearances  . . . . . . . . . . . . . . . 7
C.  Vent Cap Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
D.  PVV-SLEEVE Preparation  . . . . . . . . . . . . . . . . . . . . . . . . 12
E.  PVV-SLEEVE Installation . . . . . . . . . . . . . . . . . . . . . . . . . 13

4 Electrical Information 

 

A.  Wiring the Appliance for the PVV-SLP with IntelliFire™ 
  Touch (IFT) Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
B. Wiring the Appliance for the PVV-SLP with IntelliFire™ 
  and IntelliFire™ Plus (IPI) Controls  . . . . . . . . . . . . . . . . . 19
C.  Pairing or Re-pairing the IFT-RC400 to the Electronic 
  Control Module (IFT-ECM)  . . . . . . . . . . . . . . . . . . . . . . . . 24

5 Operating Instructions 

 

A. Installation Inspection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
B.  Power Vent Operating Instructions. . . . . . . . . . . . . . . . . . 25
C.  Maintenance   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
D.  Replace Blower/Pressure Switch . . . . . . . . . . . . . . . . . . . 26

6 Reference Materials 

 

A.  Components and Service Parts List . . . . . . . . . . . . . . . . . 29
B.  IFT-Controls and PVV-SLP Power Vent Troubleshooting  30
C.  IntelliFire™ Plus  Controls and PVV-SLP Power 
  Vent Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Summary of Contents for PVV-SLP
































Reviews: