background image

l

Turn off the power supply and unplug the dispenser to
avoid electric shock when replacing the fuse.

l

Do not place the dispenser in a humid environment. Otherwise performance of
electrical appliances can be affected. Risk of electric shock or fire.

l

Avoid water leak or drops onto the surface or into the dispenser.
Risk of electric shock or fire.

l

Unplug the power supply if the dispenser is not being used for a
long time. Risk of overheating.

l

Do not disassemble the dispenser. Risk of electric shock or damage.

l

Turn off the power supply immediately and contact your local
distributor or after-service center if you realize abnormal sound or smell.

l

Stay the dispenser out of the wall to allow the smooth ventilation
and prevent powder turn into blocks.

l

Do not put pressure on the control pad area in case of malfunction.

l

Do not use non-powder raw materials. The connecting pipe may be blocked
if using other granular or viscous raw materials, such as kernels, tea leaves,
thick soup, etc.

l

The power cord must be plugged into a 3-prong grounding-type wall receptacle,

and according to the national safety rules must be grounded.It is the personal

responsibility of the consumer to have the proper 3-prong wall receptacle
installed by a qualified electrician

l

DO NOT, UNDER ANY CIRCUMSTANCE, REMOVE THE POWER CORD
GROUNDING PRONG.

l

Do not remove any grounding wires from individual components wire servicing,

Unless the component is to be removed and replaced. It is extremely important
to replace all grounding wires when components are replaced.

l

We strongly recommend against the use of an extension cord. However if you
still elect to use an extension cord, it must meet all the standards of national
safety rules, 3-wires grounding type appliance extension cord with a 3-pins

grounding plug and a 3-slots receptacle. The rating of the extension cord should
be 230V~, 10

Cautions

S

pecifications

Model

Picture

Size

78TK

7830TL

7840TK

7840TL

37.5cm

50cm

70cm

×

×

37.5cm

50cm

70cm

×

×

37.5cm

50cm

70cm

×

×

30cm

45cm

64cm

×

×

Summary of Contents for 7830TL











Reviews: