HDBaseT HDBTM44 User Manual Download Page 14

Page: 14 / 67

4x4 HDMI 2.0 HDBaseT Matrix Switcher

IR Emitter

IR Receiver

Amplifier

Speaker

Game Console

Remote

Apply TV

A U D I O M A T R I X O U T / A R C

I R EY E

Laptop

4K Blu-Ray

IR Receiver

Receiver

Remote

H D C P LIN K

Tx R x

Display

Laptop

Router

IR Emitter

IR Receiver

Remote

Projector

IR:

HDMI:

RS232:

Audio:

Ethernet:

HDBaseT:

4. System Connection

4.1 Usage Precaution

⚫

Make sure all components and accessories included before installation.

⚫

System should be installed in a clean environment with proper temperature and
humidity.

⚫

All of the power switches, plugs, sockets, and power cords should be insulated and
safe.

⚫

All devices should be connected before power on.

4.2 System Diagram

The following diagram illustrates typical input and output connections that can be
utilized with this matrix switcher:

Speaker Speaker Speaker Speaker

Summary of Contents for HDBTM44




































































Search results

Summary of Contents for HDBTM44

Reviews:

Related manuals for HDBTM44

Brands by name

Popular brands

HDBaseT HDBTM44, User Manual

Search results

Summary of Contents for HDBTM44

Reviews:

Related manuals for HDBTM44

Brands by name

Popular brands