HDBaseT HDBTM44 User Manual Download Page 60

Page: 60 / 67

4x4 HDMI 2.0 HDBaseT Matrix Switcher

Command

Description

Command Example and

Response

EDIDGOUT[XX].

Report the EDID data from output [XX].

[XX]=01~08.

[XX]=01~04, represents HDBT output 1~4.

[XX]=05~08, represents HDMI output 1~4.

EDIDGOUT04.

EDIDOUT04:

……

EDIDM[XX]B[YY].

Copy the EDID data of output [XX] to input [YY].

[XX]=01~08, [YY]=00~04.

[XX]=01~04, represents HDBT output 1~4.

[XX]=05~08, represents HDMI output 1~4.

[YY]=00, represents all inputs.

[YY]=01~04, represents HDMI input 1~4.

EDIDM04B01.

Input 01 EDID Upgrade OK

By 04 EXT EDID!

EDIDSTA[XX].

Report the EDID status of input [XX].

[XX]=00~04.

[XX]=00, represents all inputs.

[XX]=01~04, represents HDMI input 1~4.

EDIDSTA00.

Input 01 EDID From 01

Internal EDID!

Input 02 EDID From 01

Internal EDID!

Input 03 EDID From 01

Internal EDID!

Input 04 EDID From 01

Internal EDID!

Summary of Contents for HDBTM44




































































Search results

Summary of Contents for HDBTM44

Reviews:

Related manuals for HDBTM44

Brands by name

Popular brands

HDBaseT HDBTM44, User Manual

Search results

Summary of Contents for HDBTM44

Reviews:

Related manuals for HDBTM44

Brands by name

Popular brands