HDBaseT HDBTM44 User Manual Download Page 11

Page: 11 / 67

4x4 HDMI 2.0 HDBaseT Matrix Switcher

MENU/ UP

PRESET BACK DOWN

AUDIO MATRIX OUT / ARC

IR EYE

3. Panel Description

3.1 Matrix Switcher Front Panel

①

LCD Screen:

Presents real-time operation status.

②

Power LED:

Illuminates RED when the device is in standby mode, illuminates

GREEN when device is powered on.

③

IR Sensor and its LED:

Illuminates RED when the IR sensor receives an IR

signal from the IR remote to control the matrix switcher. The IR sensor is on the
right side of the LED.

④

INPUT:

Four buttons for input source selection.

⑤

OUTPUT:

Four buttons for output channel selection.

⑥

Menu Buttons:

⚫

LOCK: Lock or unlock the front panel buttons.

⚫

PRESET: Preset setting.

⚫

MENU/

↲

: Menu or confirm button.

⚫

BACK: Go back to the previous operation.

⚫

UP: Page up.

⚫

DOWN: Page down.

3.2 Matrix Switcher Rear Panel

①

INPUT:

Four type-A female HDMI input ports to connect HDMI sources.

②

IR IN:

⚫

1~4: Four 3.5mm jacks to connect four IR receivers. Each IR input is

Summary of Contents for HDBTM44




































































Search results

Summary of Contents for HDBTM44

Reviews:

Related manuals for HDBTM44

Brands by name

Popular brands

HDBaseT HDBTM44, User Manual

Search results

Summary of Contents for HDBTM44

Reviews:

Related manuals for HDBTM44

Brands by name

Popular brands