background image

15

Use Only Genuine Hayward Replacement Parts.

Replacing Parts

Sweep Hose

• Sweep Hose Wear Rollers will experience wear when

operating in a plastered or concrete pool.

• When the Wear Rollers wear-down to the outer groove

(Wear Line) replace the Wear Rollers (P/N AEX5006A).

• Check the Sweep Hose for holes.

Some parts will wear with normal use. To insure the

high quality performance, insist on

Genuine Hayward

replacement parts (using non-Hayward replacement

parts will Void the Viio Cleaner’s Warranty).

The following parts are user replaceable and subject to

normal wear and tear.

1. Sweep Hose:

If a hole forms in the Sweep Hose, it

should be replaced. Unscrew the mender nut from the

hose and pull the Sweep Hose off the Cleaner Connector.

Attach a new Sweep Hose to the Cleaner Connector.

(Replacement Part Number: AEX6000RSHA)

2. Debris Bag:

The Debris Bag should be replaced if it

is torn.

(Replacement Part Number: AEX5500BFA)

3. Swivels:

If a swivel ceases to turn easily or leaks

while the cleaner is running, it should be replaced.

(3-Pack Replacement Part Number: AEX5000SA)

Storing the Viio Cleaner

1. Turn the Booster Pump OFF

and set the timer so

the Booster Pump will not turn on while the Viio

cleaner is out of the pool (

Never

operate the

Booster Pump without the cleaner connected).

2.

Disconnect Wall Quick Connect from the Universal Wall

Fitting. The Universal Wall Fitting may be left in place.

3.

The cleaner is constructed of the finest materials

available, however we recommend that when the Viio

cleaner is removed from the pool, it should be stored

flat on its wheels in a shaded area to protect the unit

from excessive exposure to ultraviolet solar rays.

4. Store the Sweep and Pressure Hoses straight and

flat,

not coiled

. If possible, store the hoses in the

shade.

Winterizing the Cleaner

When closing your pool for the winter completely drain

the water from the Viio Cleaner (by slowly rotating it in

all directions) and Hoses. Store the Viio Cleaner indoors
to prevent freezing the inner mechanisms.

Periodic Freezing Conditions

If you are in an area subject to periodic freezing

conditions, but pool equipment is kept in operation, it is

very important that the filtration system and Viio cleaner

be in operation during times when hard freezing occurs

(normally between 3AM and 7AM). Running the Viio

cleaner at this time will insure against damaging the

Cleaner and may prevent freezing of pool water.

Wear Roller

Wear Line (outer

groove)

Summary of Contents for Viio Turbo AE5500

























Reviews: