Hawk HA-240 Lite v3, Installation Manual

Page: 12 / 20

The illustration shows how the jumpers are set up. When the jumper cap is placed on the pins, the jumper
is ‘SHORT’. If no jumper cap is placed on the pins, the jumper is ‘OPEN’. The illustration shows a
3–pin jumper whose pin 1 and pin 2 are ‘SHORT’ when jumper cap is placed on these 2 pins.
ATTENTION: Commercial Electronics always suggests installation be performed by a certified and trained installation
technician, professional installation is a requirement to obtain full warranty. This wiring information is being provided free
of charge and on an ‘as is’ basis, without any representation or warranty to the products being installed. It is your
responsibility to insure proper installation. Commercial Electronics assumes no responsibility with regards to the accuracy
or currency of this information.
Proper installation in every case is and remains the responsibility of the installer. Commercial Electronics assumes no
responsibility resulting from an improper installation, even in reliance upon this information. Any harm or injury to the
installer is in no way the responsibility of Commercial Electronics. Any damage to the vehicle during installation or after
installation is not the responsibility of Commercial Electronics.
Jumpers setup
RED WIRE:
Connect to battery direct or constant 12v power supply.
Note: Use 7.5 amp fuse (not supplied).
BLACK WIRE:
Ground Input (-). The black wire must connect to a solid chassis ground. Clean away any paint or dirt
to ensure the best possible ground.
WHITE WIRE:
Connect to white cable of alarm C1 connector (pin 6).
J1 Petrol / Diesel Mode:
Short pin 1, pin 2 to enable petrol mode (factory default).
Short pin 2, pin 3 to enable diesel mode.
J2 Central Door Locking Time Selector:
Short pin 1, pin 2 to enable 0.8 seconds (factory default).
Short pin 2, pin 3 to enable 3.5 seconds.
J3 Automatic / Manual Gear Mode:
Short pin 1, pin 2 to enable manual gear mode (factory default).
Short pin 2, pin 3 to enable automatic gear mode.
1 2
1 2
1 2
2 3
2 3
2 3
Short Open
Siren connection guide
12
The illustration shows how the jumpers are set up. When the jumper cap is placed on the pins, the jumper
is ‘SHORT’. If no jumper cap is placed on the pins, the jumper is ‘OPEN’. The illustration shows a
3–pin jumper whose pin 1 and pin 2 are ‘SHORT’ when jumper cap is placed on these 2 pins.
ATTENTION: Commercial Electronics always suggests installation be performed by a certified and trained installation
technician, professional installation is a requirement to obtain full warranty. This wiring information is being provided free
of charge and on an ‘as is’ basis, without any representation or warranty to the products being installed. It is your
responsibility to insure proper installation. Commercial Electronics assumes no responsibility with regards to the accuracy
or currency of this information.
Proper installation in every case is and remains the responsibility of the installer. Commercial Electronics assumes no
responsibility resulting from an improper installation, even in reliance upon this information. Any harm or injury to the
installer is in no way the responsibility of Commercial Electronics. Any damage to the vehicle during installation or after
installation is not the responsibility of Commercial Electronics.
Jumpers setup
RED WIRE:
Connect to battery direct or constant 12v power supply.
Note: Use 7.5 amp fuse (not supplied).
BLACK WIRE:
Ground Input (-). The black wire must connect to a solid chassis ground. Clean away any paint or dirt
to ensure the best possible ground.
WHITE WIRE:
Connect to white cable of alarm C1 connector (pin 6).
J1 Petrol / Diesel Mode:
Short pin 1, pin 2 to enable petrol mode (factory default).
Short pin 2, pin 3 to enable diesel mode.
J2 Central Door Locking Time Selector:
Short pin 1, pin 2 to enable 0.8 seconds (factory default).
Short pin 2, pin 3 to enable 3.5 seconds.
J3 Automatic / Manual Gear Mode:
Short pin 1, pin 2 to enable manual gear mode (factory default).
Short pin 2, pin 3 to enable automatic gear mode.
1 2
1 2
1 2
2 3
2 3
2 3
Short Open
Siren connection guide
12
Siren connection guide
RED WIRE:
Connect to Pin # 18 of White wire of Alarm system
BLACK WIRE:
Ground Input (-). The black wire must connect to a solid chassis ground. Clean away any
paint or dirt to ensure the best possible ground.
Jumpers setup
The illustration shows how the jumpers are set up. When the jumper cap is placed on the
pins, the jumper is ‘SHORT’. If no jumper cap is placed on the pins, the jumper is ‘OPEN’.
The illustration shows a 3–pin jumper whose pin 1 and pin 2 are ‘SHORT’ when jumper
cap is placed on these 2 pins.
J1 Central Door Locking Time Selector:
Short pin 1, pin 2 to enable 0.8 seconds (factory default).
Short pin 2, pin 3 to enable 3.5 seconds.
J2 Dual Lock Output:
Short pin 1, pin 2 to No Dual Lock Output (factory default).
Short pin 2, pin 3 to enable Dual Lock Output.
ATTENTION: Commercial Electronics always suggests installation be performed by a certified and trained installation technician,
professional installation is a requirement to obtain full warranty. This wiring information is being provided free of charge and on
an ‘as is’ basis, without any representation or warranty to the products being installed. It is your responsibility to insure proper
installation. Commercial Electronics assumes no responsibility with regards to the accuracy or currency of this information.
Proper installation in every case is and remains the responsibility of the installer. Commercial Electronics assumes no
responsibility resulting from an improper installation, even in reliance upon this information. Any harm or injury to the installer
is in no way the responsibility of Commercial Electronics. Any damage to the vehicle during installation or after installation is
not the responsibility of Commercial Electronics.
10
The illustration shows how the jumpers are set up. When the jumper cap is placed on the pins, the jumper
is ‘SHORT’. If no jumper cap is placed on the pins, the jumper is ‘OPEN’. The illustration shows a
3–pin jumper whose pin 1 and pin 2 are ‘SHORT’ when jumper cap is placed on these 2 pins.
ATTENTION: Commercial Electronics always suggests installation be performed by a certified and trained installation
technician, professional installation is a requirement to obtain full warranty. This wiring information is being provided free
of charge and on an ‘as is’ basis, without any representation or warranty to the products being installed. It is your
responsibility to insure proper installation. Commercial Electronics assumes no responsibility with regards to the accuracy
or currency of this information.
Proper installation in every case is and remains the responsibility of the installer. Commercial Electronics assumes no
responsibility resulting from an improper installation, even in reliance upon this information. Any harm or injury to the
installer is in no way the responsibility of Commercial Electronics. Any damage to the vehicle during installation or after
installation is not the responsibility of Commercial Electronics.
Jumpers setup
RED WIRE:
Connect to battery direct or constant 12v power supply.
Note: Use 7.5 amp fuse (not supplied).
BLACK WIRE:
Ground Input (-). The black wire must connect to a solid chassis ground. Clean away any paint or dirt
to ensure the best possible ground.
WHITE WIRE:
Connect to white cable of alarm C1 connector (pin 6).
J1 Petrol / Diesel Mode:
Short pin 1, pin 2 to enable petrol mode (factory default).
Short pin 2, pin 3 to enable diesel mode.
J2 Central Door Locking Time Selector:
Short pin 1, pin 2 to enable 0.8 seconds (factory default).
Short pin 2, pin 3 to enable 3.5 seconds.
J3 Automatic / Manual Gear Mode:
Short pin 1, pin 2 to enable manual gear mode (factory default).
Short pin 2, pin 3 to enable automatic gear mode.
1 2
1 2
1 2
2 3
2 3
2 3
Short Open
Siren connection guide
12
11