background image

Page 17

For technical questions, please call 1-888-866-5797.

Item 58702 
        

Sa

FE

ty

Op

E

ra

ti

O

n

M

aint

E

nan

CE

a

SSEMBL

y

Connection (continued)

4.  With assistance, place the Hitch Coupler 

over the vehicle’s hitch ball and pull back on 
the Trigger and push down on the Handle 
until the Trigger locks in the slot.

Hitch Ball

(not included)

Handle

trigger

adjusting

nut

5.  Pull up and down on the Coupler to make sure the 

hitch ball is fitting snugly in the Coupler.  There must 
be no play between the hitch ball and Coupler.

WarninG!  tO prEVEnt SEriOUS 
inJUry: 

If there is play, tighten the 

Adjusting Nut until no play is present.
After unlocking the Handle, press back on the 
nut retaining plate (holding the Adjusting Nut in 
place) while the Nut is tightened.  After the Nut 
is tightened, 

the retaining plate must fit in 

place against the flats of the nut to prevent 
it from moving

.  This adjustment should 

be done by two people.  If the Adjusting Nut 
is too tight, the Handle will not lock.

6.  After the Adjusting Nut is properly adjusted, 

pull back on the Trigger and push down on 
the Handle until the Trigger locks in the slot.  

pull up on Handle firmly

 to make sure the Trigger 

is locked in place and the Handle cannot move.  

replace the Locking pin and r-Clip.

7.  Attach the Safety Chain to the towing vehicle’s rear 

bumper or frame with equal length on each side.  
Allow just enough chain length for unrestricted 
turning without dragging chain on the ground.

8.  Connect the Wiring Harness to the 

towing vehicle’s 12VDC system.

note:

 

Consult the operator’s manual of the towing 

vehicle for proper connection instructions.

9.  When towing the Trailer over long 

distances stop and check the tightness 
of all connections, Side Running Lights, 
and Tail Lights 

at least

 every 100 miles.

10.  Carry emergency flares and fire 

extinguisher, if required for operation in 
your state.  Carry extra fuses if towing the 
Trailer at night over long distances.

Summary of Contents for 58702





























Reviews: