10
Form No. FM5M_CN-1217
English
OPERATION
Hot Key
Temperature
Indicator
Nozzle
Power
Indicator
Cold Key
Faucet Assembly Controls
NOTE: The Hot and Cold keys on the faucet assembly can
be set to dispense after a single touch (One Touch) or
during a touch and hold (Hold Touch). The dispense
time for One Touch mode is adjustable. The dispense
time for Hold Touch mode is determined by how long
the key is held, up to 15 seconds. Refer to “Adjusting/
Changing the Dispense Mode” in this section for details.
5. Continue to use the Hot Water Dispenser as necessary.
Water will continue to enter the tank and be heated
during operation to maintain a steady supply of setpoint
temperature water.
Shutdown
1. Open the access door on the tank unit and move the
Power I/O (on/off) switch to the O (off) position.
2. Perform the “Daily Cleaning” procedure in the
MAINTENANCE section of this manual.
Locking/Unlocking the Control Panel
Use the following procedure to lock or unlock the keys on the
control panel.
Friday
10:30
SET
95
°C
°C
95
9848L
NORMAL
Display
Up Arrow
Key
Menu Key
Down Arrow
Key
Enter Key
Icon indicates
control panel
keys are locked.
FM-5 Control Panel
1. To lock the control panel:
• Press and hold the
and
keys for three seconds.
2. To unlock the control panel:
• Press and hold the
and
keys for three seconds.
General
Use the following procedures to operate the FM-5 Hot Water
Dispenser.
WARNING
Read all safety messages in the Important Safety
Information section before operating this equipment.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Hot water in unit may cause scalding injury. Be aware
and use caution during operation to avoid injury.
• Steam escaping from vent on faucet assembly may
cause scalding injury. Do not place hands or other
body parts under faucet. Be aware and use caution at
all times around faucet assembly.
Startup
1. Open the access door on the tank unit and move the
Power I/O (on/off) switch to the I (on) position.
• The control panel display will energize and show the
Main screen after it is finished starting up.
Friday
10:30
SET
95
°C
°C
95
9848L
NORMAL
Setpoint
Temperature
Tank Fill
Level
Operating
Mode
Current Water
Temperature
Filter Life
Remaining (liters)
Main Screen
• The water tank inside the tank unit will begin to fill and
heat. The tank fills in steps in order to reach setpoint
temperature quickly. The three-step tank fill level graphic
on the Main screen indicates the water level in the tank.
• The green “power” indicator on the faucet assembly will
illuminate.
• The red “temperature” indicator will flash until water in
the water tank reaches setpoint temperature. When the
water reaches setpoint temperature, the indicator will
remain on steady.
2. Place the desired container underneath the nozzle on the
faucet assembly.
3. Touch the desired key on the faucet assembly to dispense
water.
• Touch the red Hot key to dispense hot water. Hot water
will dispense for a pre-set number of seconds.
• Touch the blue Cold key to dispense room temperature
water. Room temperature water will dispense for a pre-
set number of seconds.
Summary of Contents for FLOWMAX FM-5 Series
