manualshive.com logo in svg
background image

A

AP

P1

13

37

78

87

7  ((0

01

1//0

06

6

))    

FOR YOUR SAFETY!

Do not store or use gasoline or other flammable
vapors or liquids or other combustible materials
in the vicinity of this or any other appliance. To
do so may result in an explosion or fire.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

● 

Do not touch any electrical switch; do not
use any phone in your building.

● 

Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.

● 

If you cannot reach your gas supplier, call 
the fire department.

● 

Do not return to your home until authorized 
by the gas supplier or fire department.

— 

Improper installation, adjustment, alteration,
service or maintenance can cause property
damage, personal injury, or death . Refer to this
manual. Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.

!

WARNING: If the information in these instructions is not followed exactly, 
a fire or explosion may result causing property damage, personal injury or death.

!

The purpose of this manual is twofold: one, to provide the installer with the basic directions
and recommendations for the proper installation and adjustment of the water heater; and
two, for the owner–operator, to explain the features, operation, safety precautions,
maintenance and troubleshooting of the water heater. This manual also includes a parts
list.

It is very important that all persons who are expected to install, operate or adjust this
water heater read the instructions carefully so they may understand how to perform these
operations. If you do not understand these instructions or any terms within it, seek
professional advice.

Any questions regarding the operation, maintenance, service or warranty of this water
heater should be directed to the seller from whom it was purchased. If additional
information is required, refer to the section on “If you need service.”

Do not destroy this manual. Please read carefully and keep in a safe place for future
reference.

Recognize this symbol as an indication of Important Safety Information!

California Proposition 65 Warning:

This product contains chemicals known to

the State of California to cause cancer, birth defects or other reproductive harm.

!

!

Residential 40 and 50 Gallon

Use & Care Manual

With Installation Instructions for the Installer

Printed in USA

DESIGN

CERTIFIED

®

WARNING:

This water heater is not

suitable for use in manufactured (mobile) homes!

!

®

Water Heaters

Gas Residential

Manufactured under trademark license by:

Rheem Manufacturing Company

2600 Gunter Park Drive East, Montgomery, AL 36109-1413

Содержание Powervent AP13787





































Отзывы: