Hasselblad Flextight 949 User Manual Download

Page: 2 / 36

Slide Feeder for Flextight 949 Scanners, Part No 75020088 revision B.

The information in this manual is furnished for informational use only, is subject to change

without notice, and should not be construed as a commitment by Hasselblad A/S.

Hasselblad A/S assumes no responsibility or liability for any errors or inaccuracies that may appear

in this manual.

Hasselblad A/S assumes no responsibility or liability for loss or damage incurred during or as a

result of using Hasselblad software or products.

Hasselblad, FlexColor, Flextight, FlexFrame and Ixpress are trademarks of Hasselblad A/S. Adobe

and Adobe Photoshop are trademarks of Adobe Systems, Inc. Macintosh, Mac OS, ColorSync, and

FireWire are registered trademarks of Apple Computer, Inc.

Printed in Denmark.

Summary of Contents for Flextight 949





































Search results

Summary of Contents for Flextight 949

Reviews:

Related manuals for Flextight 949

Brands by name

Popular brands

Hasselblad Flextight 949, User Manual

Search results

Summary of Contents for Flextight 949

Reviews:

Related manuals for Flextight 949

Brands by name

Popular brands