HART HPCS25, Operator'S Manual, Page: 3 / 36

3 - English
CUTTING PROCEDURES
DANGER:
Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or motor
housing.
If both hands are holding the saw, they cannot
be cut by the blade.

Do not reach underneath the workpiece. The guard
can not protect you from the blade below the workpiece.

Adjust the cutting depth to the thickness of the
workpiece.
Less than a full tooth of the blade teeth
should be visible below the workpiece.

Never hold the workpiece in your hands or across
your leg while cutting. Secure the workpiece to a
stable platform.
It is important to support the work
properly to minimize body exposure, blade binding, or
loss of control.

Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting tool
may contact hidden wiring.
Contact with a “live” wire
will also make exposed metal parts of the power tool
“live” and could give the operator an electric shock.

When ripping, always use a rip fence or straight edge
guide.
This improves the accuracy of cut and reduces
the chance of blade binding.

Always use blades with correct size and shape
(diamond versus round) of arbor holes.
Blades that
do not match the mounting hardware of the saw will run
off-center, causing loss of control.

Never use damaged or incorrect blade washers or
bolt.
The blade washers and bolt were specially designed
for your saw, for optimum performance and safety of
operation.
KICKBACK CAUSES AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched, jammed or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece toward the operator;

When the blade is pinched or jammed tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator;

If the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into the
top surface of the wood causing the blade to climb out
of the kerf and jump back toward the operator.
GENERAL POWER TOOL SAFETY WARNINGS

Keep cutting tools sharp and clean.
Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.

Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and
free from oil and grease.
Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
BATTERY TOOL USE AND CARE

Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.

Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create
a risk of injury and fire.

When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another.
Shorting the
battery terminals together may cause burns or a fire.

Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the
battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or
modified.
Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or risk
of injury.

Do not expose a battery pack or tool to fire or
excessive temperature.
Exposure to fire or temperature
above 265° F may cause explosion.

Follow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specified in the instructions.
Charging improperly or at
temperatures outside the specified range may damage
the battery and increase the risk of fire.
SERVICE

Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This
will ensure that the safety of the power tool is maintained.

Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
CIRCULAR SAW SAFETY WARNINGS