Harris NXAMP3801HDI Hardware Installation And User'S Manual Download Page 61

Page: 61 / 76

Maintenance

This chapter provides safety guidelines, tools and access information about maintaining your
NXAMP3801HDX/HDI system.

Installation Tools

You will need the following tools for the safe and proper installation of your system.



Phillips screw driver



Anti-static strap



Small tip screwdriver

Important Safety Guidelines

The NXAMP3801HDX/HDI should only be accessed and serviced by technically qualified
personnel or technicians.

Turn off all peripheral devices and the power supply connected to the system.

Unplug all power cords from the system or wall outlets.

Disconnect all the cables and label the cables for easy identification.

Use a grounded wrist strap designed to prevent static discharge when handling components.

Chassis Cover

Removal

Figure 8-1

Main Power Switch Location

Summary of Contents for NXAMP3801HDI













































































Search results

Summary of Contents for NXAMP3801HDI

Reviews:

Related manuals for NXAMP3801HDI

Brands by name

Popular brands

Harris NXAMP3801HDI, Hardware Installation And User'S Manual

Search results

Summary of Contents for NXAMP3801HDI

Reviews:

Related manuals for NXAMP3801HDI

Brands by name

Popular brands