background image

InstallatIon and operatIon Manual for WInd and sun screen sl400

09/12 

|

 10

7. user Info

7.1. 

basic information

Before operating the SL400, you need to have sufficient knowledge of the product. the 
contents of this manual is a sound basis for a smooth, continuous operation and a long 
service life of this product. 
also, for the sake of personal safety, it is important to follow these instructions. failure to 
follow these instructions relieves the manufacturer of all liability.
Keep this installation and operation manual handy for future reference. Should the SL400 
be handed over to a third party, then this manual must also be supplied to the new owner.  

7.2.  safety instructions

a number of precautions must be taken for the safe operation and maintenance of the 
SL400. Installation, maintenance or repair of the wind and sun screen by anyone other 
than a recognized fitter can be a safety hazard or cause injury. for the safety of everyone 
concerned, please take note of the instructions, warnings and directions below! If in doubt, 
always contact your supplier. always take care when using the sun screen!

 

!

please read this manual carefully before operation or maintenance.

 

!

Installation, maintenance and repairs must only be carried out by a qualified and 
experienced technician!

 

!

Malfunctions, which can impair the safety, must be reported and repaired 
immediately.

 

!

the product may only be operated by persons who have been instructed by the 
installer about the correct mode of operation. It is strictly forbidden to allow children 
to operate the SL400! they may put themselves at risk while operating the screen.

 

!

when opening and closing the screen, always keep the SL400 in sight and make 
sure that there are no persons (children!) or obstacles within its range of movement. 

 

!

the safety lock must always be engaged when the screen is open, to prevent it from 
unexpectedly retracting.

 

!

watch out for hands/fingers when hooking up the pull rod to the system, as well as 
when closing the screen. danger of pinching!

 

!

If work is being carried out in the vicinity of the screen, then make sure it is always 
closed.

 

!

ensure that the sun screen is regularly inspected and maintained..

danGer! BecauSe of tHe InteGrated SprInG SYSteM, tHere IS aLwaYS 

tenSIon on tHe SL400. for tHIS reaSon aLL repaIrS or dISMantLInG 
MuSt Be carrIed out BY profeSSIonaLLY traIned and quaLIfIed 
Staff. aLwaYS taKe care wHen uSInG tHIS Sun Screen!

Summary of Contents for SL400


















Reviews: