background image

53

1018856 

08/2018  V04

Checking of electric connections

 

Lethal electric shock by touching live parts!

In any case of defects of the cable sheath the system must be shut down immediately and the damaged cable should be 
replaced. Do not make any temporary repairs on the connection cables. 

•  Connection cord should be periodically checked for damage and replaced if necessary. 
•  Check optionally installed power chains for defects. 
•  Protective conductor connections should be in a good condition and tightness checked at regular intervals.  
  Replace if necessary.

Control of mechanical fasteners 

The fastening screws and the load of the housing must be checked regularly.

Maintenance intervals for battery backed motor feedback systems

Please note the information on battery life time in the chapter "

Motor Feedback Systems

"!

DANGER

10.   Decommissioning and Disposal

The gears, servo actuators and motors from Harmonic Drive AG contain lubricants for bearings and gears as well as electronic 
components and printed circuit boards. Since lubricants (greases and oils) are considered hazardous substances in accordance 
with health and safety regulations, it is necessary to dispose of the products correctly. Please ask for safety data sheet where 
necessary.

•  Batteries do not contain hazardous materials according to EC directives 91/157/EEC, 93/86/EEC, and 2011/65/EU 
    (RoHS directive) 
•  EC battery directive 2006/66/EC has been implemented by most EC member states, 
•  According to the EU Battery Directive, Lithium batteries are marked with the symbol of the crossedout wheeled bin
    (see figure). The symbol reminds the end user that batteries are not permitted to be disposed of with household waste, but
    must be collected separately.
•  A disposal service is offered upon request by Harmonic Drive AG. 

ADVICE

ADVICE

Summary of Contents for LynxDrive 14C









































































Reviews: