Harman Super Magnum Coal Stoker Installation & Owner'S Manual Download Page 1

Page: 1 / 40

3-90-02702R8_11/13

www.harmanstoves.com

Please read this entire manual before

installation and use of this coal - burning

room heater.

Failure to follow these instructions could

result in property damage, bodily injury

or even death.

Tested and approved for anthracite rice coal fuel only.

Burning of any other type of fuel voids your warranty.

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room as

stove.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other

flammable materials.

• Keep clothing, furniture, draperies and other flammable

materials away.

HOT SURFACES!

Glass and other surfaces are hot

during operation and cool down.

To obtain a French translation of this manual, please

contact your dealer or visit www.harmanstoves.com

Pour obtenir une traduction française de ce manuel, s’il

vous plaît contacter votre revendeur ou visitez www.

harmanstoves.com

NOTE

WARNING

Installation & Owner’s Manual

Care and Operation

Model(s):

Super Magnum Coal Stoker

NOTICE: SAVE THESE INSTRUCTIONS

CAUTION

• Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

• Do not overfire - If any external part starts to glow, you

are overfiring. Reduce feed rate. Overfiring will void

your warranty.

• Comply with all minimum clearances to combustibles

as specified. Failure to comply may cause house fire.

Check building codes prior to installation.

• Installation MUST comply with local, regional, state

and national codes and regulations.

• Contact local building or fire officials about restrictions

and installation inspection requirements in your area.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

Call your dealer for questions on Installation, Operation, or Service.

Summary of Contents for Super Magnum Coal Stoker









































Search results

Summary of Contents for Super Magnum Coal Stoker

Reviews:

Related manuals for Super Magnum Coal Stoker

Brands by name

Popular brands

Harman Super Magnum Coal Stoker, Installation & Owner'S Manual

Search results

Summary of Contents for Super Magnum Coal Stoker

Reviews:

Related manuals for Super Magnum Coal Stoker

Brands by name

Popular brands