Harman Super Magnum Coal Stoker Installation & Owner'S Manual Download Page 10

Page: 10 / 40

Super-Magnum Coal Stoker Stove

Do Not Burn Wet Coal!

3-90-02702R8_11/13

B. Clearances To Combustibles

C
D

Parallel

Installation

Inches

Millimeters

Back Wall To Unit Hopper

Side Wall To Unit

Back Wall To Flue Connector

Side Wall To Flue Connector

2 51

17 432

24 610

34 864

Corner

Installation

Inches

Millimeters

Walls to Unit Body

Walls to Flue Connector

15 381

24 610

C. Floor Protection Requirements

Floor protection must be of a non-combustible material. It

must be located under the appliance and extend beyond

the appliance according to the measurements below. Floor

protection must also extend under any horizontal sections

of chimney connector and 2" (50.8mm) beyond each side of

the connector.

DANGER:

The appliance legs may not be removed for

installation.

Minimum Size floor protection is 49½" Deep By 42¾" Wide.

Floor Protection

Requirements

Inches

Millimeters

Sides- USA /CANADA *

Rear- USA

8 203

12 305

Front- USA /CANADA *

18 457

54"

Alternate floor protector dimension may be used as long

as they satisfy the measurement requirements shown

above.
Minumum size floor protection for a corner installation

hearth pad is 54" x 54" (USA ONLY).

Summary of Contents for Super Magnum Coal Stoker









































Search results

Summary of Contents for Super Magnum Coal Stoker

Reviews:

Related manuals for Super Magnum Coal Stoker

Brands by name

Popular brands

Harman Super Magnum Coal Stoker, Installation & Owner'S Manual

Search results

Summary of Contents for Super Magnum Coal Stoker

Reviews:

Related manuals for Super Magnum Coal Stoker

Brands by name

Popular brands