Harman Super Magnum Coal Stoker Installation & Owner'S Manual Download Page 8

Page: 8 / 40

Super-Magnum Coal Stoker Stove

Do Not Burn Wet Coal!

3-90-02702R8_11/13

D. Pre- Use Check List

Place the appliance in a location near the

final installation and follow the procedures

below:

Open the appliance and remove all articles

packed inside. Inspect all items for shipping

damage. Notify dealer of any missing or

damaged goods.

All safety warnings have been read and

followed precisely.

This Owner's Manual has been read in it's

entirety.

Floor protection requirements have been

read and followed.

The flue connector has been installed in

accordance with the instructions herein.

The proper clearances from the appliance

and chimney connector to combustibles

have been met.

The masonry chimney has been cleaned

and inspected by a professional, or the

factory built metal chimney is installed

according to the manufacturers instructions.

The chimney meets the minimum height

requirements.

10.

All labels and hang tags have been removed

from the glass.

11.

All plated surfaces have been wiped clean,

if applicable.

12.

The room sensor and any additional cable

has been installed properly.

13.

A properly grounded electrical receptacle is

available within reach of the unit's power

cord.

Inspect appliance and components for

damage. Damaged parts may impair safe

operation.

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

• Installation and use of any damaged appliance.

• Modification of the appliance.

• Installation other than as instructed by Hearth &

Home Technologies.

• Operating appliance without fully assembling all

components.

• Operating appliance without legs attached.

• Do NOT Overfire.

Or any such action that may cause a fire hazard.

Fire Risk

Hearth & Home Technologies disclaims

any responsibility for, and the warranty will

be voided by, the following actions:

WARNING

Summary of Contents for Super Magnum Coal Stoker









































Search results

Summary of Contents for Super Magnum Coal Stoker

Reviews:

Related manuals for Super Magnum Coal Stoker

Brands by name

Popular brands

Harman Super Magnum Coal Stoker, Installation & Owner'S Manual

Search results

Summary of Contents for Super Magnum Coal Stoker

Reviews:

Related manuals for Super Magnum Coal Stoker

Brands by name

Popular brands