Safety Information
5
P R O T E C T I O N F R O M E L E C T R I C S H O C K
• Do not remove any cover from the fixture except as described under “Service and maintenance” on
• To ensure that the fixture’s IP65 rating has not been affected by removal of a cover, test that the fixture is
correctly sealed after reassembly using a vacuum tester as described in this manual.
• Disconnect the fixture from AC mains power before servicing it and when it is not in use.
• Ensure that the fixture is electrically connected to ground (earth).
• Use only a source of AC mains power that complies with local building and electrical codes and has both
overload and ground-fault (earth-fault) protection.
• Consult a qualified electrician to ensure correct branch circuit conductor.
• The fixture accepts AC mains power at 100-240 VAC (nominal), 50/60 Hz. Do not connect the fixture to
mains power that is not within this range.
• Do not connect devices to power in a chain or circuit that will exceed the electrical ratings of any cable or
connector used in the circuit.
• Power input cables must be rated 16 A minimum, 12 AWG or 1.5 mm
2
minimum conductor size and
heat-resistant to 90° C (194° F) minimum. Cables must have three conductors and an outer cable
diameter of 6 - 12 mm (0.24 - 0.47 in.). In North America the cable must be UL/CSA-recognized, hard
usage, type SJT, SJOOW or better. In the EU, the cable must be type HO5VV-F, H07RN-F or better.
• Connect only a Neutrik powerCON TRUE1 NAC3FX-W (TOP) type cable connector to the power input
socket.
• If operating outdoors, in wet conditions or in conditions where condensation may appear, arrange cables
so that they arrive from below connectors. Create a ‘drip loop’ if necessary, but do not allow heavy cable
runs or loops of cable to hang from connectors.
• Before using the fixture, check that all power distribution equipment, connectors and cables are in perfect
condition and rated for the current requirements of all connected devices.
• Isolate the fixture from power immediately if the power plug or any seal, cover, cable, or other component
is damaged, defective, deformed or showing signs of overheating. Do not reapply power until repairs have
been completed.
• The ERA 500 Hybrid IP contains components that are accessible and live at high voltage while the fixture
is connected to power and that remain under tension for up to five minutes after power is disconnected.
Wait for at least five minutes after disconnecting from power before opening any of the fixture’s covers (if
the fixture has been in use, allow to cool for 60 minutes before handling).
• Refer any service operation not described in this manual or in the ERA 500 Hybrid IP User Guide to
Martin Service or an authorized Martin Service partner.
L A M P S A F E T Y
• Prolonged exposure to an unshielded discharge lamp can cause eye and skin burns. Do not stare directly
into the light output. Never look at an exposed lamp while it is lit. Do not operate the fixture with missing or
damaged covers, shields, lenses or ultraviolet screens.
• A hot discharge lamp is under pressure and can explode without warning. Allow the fixture to cool for at
least 60 minutes and protect yourself with safety glasses and gloves before handling a lamp or carrying
out any service work inside the fixture.
• Replace the lamp immediately if it becomes visually deformed, damaged or in any way defective
• Monitor hours of lamp use and lamp intensity and replace the lamp when it reaches the limit of its service
life as specified in this product’s specifications or by the lamp manufacturer.
• Install only a lamp that is specifically approved by Martin for this product.
• If the clear bulb of a discharge lamp is broken, it releases a small quantity of mercury and other toxic
gases. Have suitable mercury vapor protection masks ready when servicing the fixture and use them if
there is any risk that potentially harmful vapors may be inhaled. If a discharge lamp breaks in a confined
area, evacuate the area and ventilate it thoroughly. If there is a possibility that the lamp has exploded or
the bulb has broken inside the fixture, move the fixture outdoors or make it safe by using an air extractor
system that will remove any potentially harmful vapor, then put on a mercury vapor protection mask and
safety gloves before opening the fixture.
• Wear nitrile gloves when handling a broken discharge lamp. Treat broken or used discharge lamps as
hazardous waste and send to a specialist for disposal.
• The wires that supply power to the lamp carry high voltage. Wear insulating safety gloves and do not
touch the lamp wiring or lamp wiring connectors when carrying out lamp adjustment.
