Harman AMX NI-2100 Hardware Reference Manual Download Page 6

Introduction

6

NI-2100/3100/4100 - Hardware Reference Guide

Timekeeper

The Controllers use a combination lithium battery and clock crystal package called a 

Timekeeper

. Only one 

Timekeeper

 unit is 

installed within a given NI controller. The battery can be expected to have up to 3 years of usable life under very adverse conditions. 

Actual life is appreciably longer under normal operating conditions. 



This calculation is based on storing the unit without power in 50° C (120° F) temperature until battery levels are no longer 

acceptable. 



The part number for a replacement battery is 

57-0032

CAUTION:  

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO 

THE INSTRUCTIONS

NI-2100

The NI-2100 (

FG2105-04

) is ideal for control and automation of medium-sized rooms and multi-room applications. The NI-2100 

has 64MB of onboard RAM and is Device Discovery enabled to simplify programming by standardizing device and function 

definitions, default touch panel button assignments, and control and feedback methods.

NI Controllers - Features (Cont.)

NI-4100 NetLinx Integrated Controllers

Name / FG#

Features

NI-4100 Controller 

(FG2105-06)

• 7 Configurable RS-232 / RS-422 / RS-485 Serial ports
• 8  Relays
• 8 IR / Serial ports
• 8 Digital I/O ports
• 3 Communication Networks: AxLink, ICSNet and Ethernet (TCP/IP)
• 4 NetLinx Control Card Expansion slots that support all NXC control cards
• 404 MIPS processor speed
• 64  MB  RAM
• 512  MB  CompactFlash  (upgradeable to 4 GB)
• 1 MB Non-Volatile Memory
• AMX Device Discovery enabled
• JITC Compliant

NI-4100/256 Controller 

(FG2105-26)

Same as the NI-4100 (above), but with 256 MB RAM.

Note: The NI-4100/256 is not JITC Compliant.

FIG. 1  

NI-2100

LINK/ACT LED

STATUS LED

INPUT LED

OUTPUT LED

RS-232/422/485 Status LEDs

RELAY Status LEDs

IR/SERIAL Status LEDs

I/O Status LEDs

front

rear

RS-232/422/485 (Ports 1-3)

ICSNet/ICSHub Ports

(provided by optional 

ICSNet daughter card)

Relays (Port 4)

I/O (Port 9)

IR/Serial (Ports 5-8)

PROGRAM Port

CONFIGURATION DIP Switch

ID Pushbutton

ETHERNET

10/100 Port

AxLink Port

12 VDC PWR Connector

Summary of Contents for AMX NI-2100






























Reviews: