manualshive.com logo in svg

Harman AMX NI-2100, Hardware Reference Manual

Share
Download
Harman AMX NI-2100 Hardware Reference Manual Download Page 4

Table of Contents

4

NI-2100/3100/4100 - Hardware Reference Guide

DB9 Device Port: Connections and Wiring ...................................................................... 23
ICSNet Port: Connections and Wiring ............................................................................  24
ICSHub OUT Port: Connections and Wiring ...................................................................  24
Relay Port: Connections and Wiring................................................................................ 25

Relay Connections ................................................................................................................................  25

Input/Output (I/O) Port: Connections and Wiring ......................................................... 25
IR/Serial Port: Connections and Wiring.......................................................................... 26
NetLinx Control Card Slot Connector (NI-4100 only) .................................................... 26
LAN (Ethernet/RJ-45 Port): Connections and Wiring ....................................................  27

LAN LEDs ...............................................................................................................................................  27
LAN Ports Used By the Integrated Controller ......................................................................................  27

Summary of Contents for AMX NI-2100






























Reviews:

No comments

Brands by name

Popular brands

Load more brands