background image

Harman®  •  Accentra 52i Installation Manual_R16  •  2013 -___  •  09/15

28

3-90-00574i

Reference Material 

 

A. Safety Reminders

When installing the Harman® Accentra 52i Pellet Insert, 

respect basic safety standards. Read these instructions 

carefully before you attempt to install or operate the 

Accentra 52i Pellet Insert. Failure to do so may result 

in damage to property or personal injury and may void 

the product warranty.
Consult  with  your  local  building  code  agency  and 

insurance  representative  before  you  begin  your 

installation  to  ensure  compliance  with  local  codes, 

including the need for permits and follow-up inspections.

MOBILE/MANUFACTURED HOME GUIDELINES DO 

NOT ALLOW INSTALLATION IN A SLEEPING ROOM.

THE STRUCTURAL INTEGRITY OF THE MOBILE 

HOME FLOOR, WALL, AND CEILING/ROOF MUST BE 

MAINTAINED.

THE STOVE IS HOT WHILE IN OPERATION.
KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. 

CONTACT MAY CAUSE SKIN BURNS.

KEEP COMBUSTIBLE MATERIALS SUCH AS GRASS, 

LEAVES, ETC. AT LEAST 3 FEET AWAY FROM THE 

POINT DIRECTLY UNDER THE VENT TERMINATION.

USE OF IMPROPER FUELS, FIRE STARTERS OR 

ALTERING THE STOVE FOR HIGHER HEAT OUTPUT 

MAY CAUSE DAMAGE TO THE STOVE AND COULD 

RESULT IN A HOUSE FIRE. USE ONLY APPROVED 

FUELS AND OPERATION GUIDELINES

DO NOT USE MAKESHIFT COMPONENTS OR 

OTHER COMPROMISES WHEN INSTALLING THIS 

APPLIANCE.

WARNING

!

WARNING

!

WARNING

!

CAUTION

!

CAUTION

!

CAUTION

!

Due to high temperatures, this stove should be placed 

out of traffic and away from furniture and draperies.
Children and adults should be alerted to the hazards 

of high surface temperatures and should stay away to 

avoid burn to skin and/or clothing.
Young children should be carefully supervised when 

they are in the same room as the stove.
Clothing and other flammable materials should not be 

placed on or near this stove.
Installation and repair of this stove should be done by 

a  qualified  service  person. The  appliance  should  be 

inspected before use and at least annually by a qualified 

service person. More frequent cleaning will be required. 

It is imperative that control compartments, burners, and 

circulating air passageways of this stove be kept clean.

CAUTION

!

This appliance must be vented to the outside.

Summary of Contents for Accentra 52i Pellet Insert































Reviews: